DLC Display Co., Limited
MODEL No: DLC1500AMG-T-1
TEL: 86-755-86029824 FAX: 86-755-86029827 E-MAIL:
[email protected] WEB: www.dlcdisplay.com
Module Name: DLC1500AMG-T-1
Ver1.0
Record of Revision
Date 2011-09-08 Revision No. 1.0 Rev 1.0 was issued Summary
http://www.dlcdisplay.com
Email:
[email protected]
Page 2 of 19
Module Name: DLC1500AMG-T-1
Ver1.0
1. Scope
This data sheet is to introduce the specification of DLC1500AMG-T-1 active matrix TFT module. It is composed of a color TFT-LCD panel, driver ICs, TCON, Touch panel and a backlight unit. The 15.0” Display area contains 1024(RGB) X 768 pixels.
2. Application
Digital equipments which need color display, monitor, POS, video systems.
3. General Information
Item Size Resolution Interface Technology type Pixel pitch Pixel Configuration Outline Dimension (W x H x D) Active Area Display Mode Backlight Type 15.0 1024(RGB) X 768 LVDS a-Si TFT 0.297x0.297 R.G.B. Vertical Stripe 326.50x 253.5 x 15.4 304.13 x 228.10 Transmissive Normally White White-LED mm mm / / Contents inch / / / mm Unit
http://www.dlcdisplay.com
Email:
[email protected]
Page 3 of 19
Module Name: DLC1500AMG-T-1
Ver1.0
4. Outline Drawing
http://www.dlcdisplay.com
Email:
[email protected]
Page 4 of 19
Module Name: DLC1500AMG-T-1
Ver1.0
5. Interface signals
5.1 CN1 for LVDS No Symbol 1 VCC 2 VCC 3 GND 4 6-8 bit SEL 5 RIN06 RIN0+ 7 GND 8 RIN19 RIN1+ 10 GND 11 RIN212 RIN2+ 13 GND 14 CLKIN15 CLKIN+ 16 GND 17 18 19 20 RIN3RIN3+ NC/GND NC/GND Description 3.3V Power Supply 3.3V Power Supply Power Ground Select 6 or 8 bits LVDS input (“H”: 8 bits; GND/NC: 6 bits) Negative (-) LVDS differential data input Positive (+) LVDS differential data input Power Ground Negative (-) LVDS differential data input Positive (+) LVDS differential data input Power Ground Negative (-) LVDS differential data input Positive (+) LVDS differential data input Power Ground Clock Signal (-) Clock Signal (+) Power Ground Negative (-) LVDS differential data input (Used for 8 bits LVDS input, NC for 6 bits) Positive (+) LVDS differential data input (Used for 8 bits LVDS input, NC for 6 bits) Test function pin (don’t set this pin to High) Test function pin (don’t set this pin to High) Remarks
Low or Open
CN1: 185083-20121-1 (Produced by Dachang) or equivalent.
5.2 CN2 for LED Backlight
No 1 2 3 4 5 Symbol VCC GND Enable Dimming NC Description 12V GND 5V-On / 0V-Off PWM Dimming or Analog Dimming NC Remark
CN2: MSB24038P5 (Produced by STM) or equivalent..
5.3 Position of plugs and a socket
http://www.dlcdisplay.com
Email:
[email protected]
Page 5 of 19
Module Name: DLC1500AMG-T-1
Ver1.0
5.4 Connection between receiver and transmitter for LVDS
Note1: The lowest bit (RA0, GA0, BA0, RB0, GB0, BB0), the most upper bit (RA7, GA7, BA7, RB7, GB7, BB7) Note2: Connecting cable between LCD panel’s connector and transmitter should use 100Ω twisted line. Note3: If only Hsync and Vsync, the product don’t work. Make sure DE signal has been input.
http://www.dlcdisplay.com
Email:
[email protected]
Page 6 of 19
Module Name: DLC1500AMG-T-1
Ver1.0
6. Absolute maximum Ratings
6.1. Electrical Absolute max. ratings
Item Power Supply Voltage Input voltage for signals Light bar peak forward current Symbol VCC Vi IF MIN -0.3 -0.3 -MAX 6.0 3.3 150 Unit V V mArms Remark Ta=25℃ Ta=25℃
Note1: Display signals are DA0+/-, DA1+/-, DA2+/-, DA3+/- and CKA+/-, DB0+/-, DB1+/-, DB2+/-, DB3+/- and CKB+/-. Note2: Function signal is MSL.
6.2. Environment Conditions
Item Operating Temperature Storage Temperature Symbol TOPR TSTG MIN -20 -30 MAX 70 80 Unit ℃ ℃ Remark
http://www.dlcdisplay.com
Email:
[email protected]
Page 7 of 19
Module Name: DLC1500AMG-T-1
Ver1.0
7. Electrical Specifications
7.1 Electrical characteristics for LCD GND=0V, Ta=25℃ Item Power Supply Voltage Power Supply Current Permissible ripple voltage Differential input voltage Differential input Low Level Threshold voltage for LVDS receiver High Level Input voltage width for LVDS receiver Rush current Terminating resistor Symbol VCC ICC VRP ∣Vid∣ VTL VTH Vi Irush RT MIN 3.0 --250 -100 0 --TYP 3.3 -------100 MAX 3.6 325 Note 1 100 450 -100 2.4 1.5 -Unit V mA mV mV mV mV V A Ω At VCC=3.3V For VCC -at VCM = 1.25V Note 2 -Note 3 -Remark
Note1: All black pattern; Note2: Common mode voltage for LVDS receiver; Note 3: Measurement Conditions:
http://www.dlcdisplay.com
Email:
[email protected]
Page 8 of 19
Module Name: DLC1500AMG-T-1
7.2 Drive for Backlight Parameter Light bar operation current Light bar operation Voltage Symbol ILED VLED min. -17.5 typ. 80 -max. -23.1 Unit mArms Vrms Note 1
Ver1.0 Ta=25℃
Remarks Operating with fixed driving current
Note1: The backlight of this product is made up of 1 light bar, LED to be 3020, 28 pieces, 7 serials and 2x2 parallels. Note2: The light bar can work normally if the PWM dimming ratio range is from 0% to 100% and the operation current is 80mA.
7.3 Block Diagram
Note: System ground (GND), FG (Frame g.