DatasheetsPDF.com

PCF1E470MCL4GS Dataheets PDF



Part Number PCF1E470MCL4GS
Manufacturers Nichicon
Logo Nichicon
Description ALUMINUM ELECTROLYTIC CAPACITORS
Datasheet PCF1E470MCL4GS DatasheetPCF1E470MCL4GS Datasheet (PDF)

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CF Chip Type, Standard series Ultra-low ESR, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC). CV High Voltage CG Higher Capacitance, CS Long Life CF Low ESR CJ Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 2.5 to 25V Rated Capacitance .

  PCF1E470MCL4GS   PCF1E470MCL4GS



Document
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CF Chip Type, Standard series Ultra-low ESR, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC). CV High Voltage CG Higher Capacitance, CS Long Life CF Low ESR CJ Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 2.5 to 25V Rated Capacitance Range 3.3 to 1500µF Capacitance Tolerance ± 20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C 1.25 Z– 55°C / Z+20°C 1.25 (100kHz) Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Resistance to Soldering Heat Marking After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In the case of peak temp, less than 250°C, reflow soldering shall be two times maximum. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Navy blue print on the case top Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage .


PCF1E330MCL1GS PCF1E470MCL4GS PCF1E470MCL1GS


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)