Document
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LV Radial Lead Type, Long Life Assurance series
High voltage (to 63V), Low ESR, High ripple current. Long life of 3000 hours at 105°C. Radial lead type: Lead free flow soldering condition correspondence. Compliant to the RoHS directive (2002/95/EC).
LV
LFHigh Voltage Long Life
Specifications
Item
Performance Characteristics
Category Temperature Range – 55 to +105°C
Rated Voltage Range
16 to 63V
Rated Capacitance Range 22 to 470µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics (Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25 (100kHz) Z– 55°C / Z+20°C 1.25
Endurance
The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 3000 hours at 105°C.
Capacitance change tan δ ESR ( 1) Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value
Damp Heat (Steady State)
The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH.
Capacitance change tan δ ESR ( 1) Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value
Resistance to Soldering Heat
After soldering the capacitor under the soldering conditions prescribed here as preheat at 150 to 200°C for 60 to 180 seconds and peak temperature at 265°C for 10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side.
Capacitance change tan δ ESR ( 1) Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering.
LV 82 V 012 φ D+0.5 MAX. P 0.5
Dimensions
Capacitance
Resin coated Case Voltage(V:35V)
Tinned lead Wire
Series
Lot. No.
L+0.5MAX.
φd 15MIN
4MIN
Type numbering system (Example : 35V 82µF)
1 2 3 4 5 6 7 8 9 10 11 12
P LV 1V 820MDL 1
Size code Configuration Capacitance tolerance (±20%) Rated capacitance (82µF) Rated voltage (35V)
Series name Type
(mm)
Size φ8 × 9L φ8 × 12L φ10 × 13L
φD 8.0 8.0 10.0 Voltage
L 8.5 11.5 12.5 P 3.5 3.5 5.0 φd 0.6 0.6 0.6
V 16 20 25 35 50 63 Code C D E V H J
Please refer to page 20 about the end seal configulation.
Configuration
φ D×L 8×9 8 × 12 10 × 13
Code
CL DL DL
Dimension table in next page.
CAT.8100Z
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LVseries
Standard Ratings
Rated Voltage (V) code
Surge Voltage (V)
Rated Capacitance (µF)
16 (1C)
18.4
220 270 470
20 (1D)
23.0
150 220 330
25 (1E)
28.7
120 150 270
35 (1V)
40.2
56 82 150
50 (1H)
57.5
33 39 68
63 (1J)
72.4
22 27 47
Case Size φD × L (mm)
8×9 8 × 12 10 × 13 8×9 8 × 12 10 × 13 8×9 8 × 12 10 × 13 8×9 8 × 12 10 × 13 8×9 8 × 12 10 × 13 8×9 8 × 12 10 × 13
tan δ
0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12
Leakage Current
ESR (mΩ)
Rated Ripple
(µA) (at 100kHz 20°C) (mArms)
Part Number
704 864 1504 600 880 1320 600 750 1350 392 574 1050 330 390 680 277 340 592
26
2100
PLV1C221MCL1
24
2500
PLV1C271MDL1
23
2900
PLV1C471MDL1
27
2000
PLV1D151MCL1
25
2400
PLV1D221MDL1
24
2800
PLV1D331MDL1
28
2000
PLV1E121MCL1
26
2400
PLV1E151MDL1
25
2800
PLV1E271MDL1
29
1900
PLV1V560MCL1
27
2300
PLV1V820MDL1
26
2700
PLV1V151MDL1
32
1900
PLV1H330MCL1
29
2200
PLV1H390MDL1
28
2600
PLV1H680MDL1
35
1800
PLV1J220MCL1
33
2100
PLV1J270MDL1
29
2600
PLV1J470MDL1
Rated ripple current (mArms) at 105°C 100kHz
Taping specifications are given in page 20, 21, 22. Please refer to page 3 for the minimum order quantity.
CAT.8100Z
.