Document
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LS Radial Lead Type, Long Life Assurance series
Ultra-low ESR, High ripple current. Load life of 5000 hours at 105°C. Radial lead type : Lead free flow soldering condition correspondence. Compliant to the RoHS directive (2002/95/EC).
LS
Long Life LF
Specifications
Item
Performance Characteristics
Category Temperature Range – 55 to +105°C
Rated Voltage Range
2.5 to 16V
Rated Capacitance Range 100 to 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics (Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25 (100kHz) Z– 55°C / Z+20°C 1.25
Endurance
The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 5000 hours at 105°C.
Capacitance change tan δ ESR ( 1) Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value
Damp Heat (Steady State)
The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH.
Capacitance change tan δ ESR ( 1) Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value
Resistance to Soldering Heat
After soldering the capacitor under the soldering conditions prescribed here as preheat at 150 to 200°C for 60 to 180 seconds and peak temperature at 265°C for 10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side.
Capacitance change tan δ ESR ( 1) Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Resin coated Case Voltage(A:10V)
Silvered lead Wire
Type numbering system (Example : 10V 270µF)
1 2 3 4 5 6 7 8 9 10 11 12
P L S 1 A 2 7 1 MDO 1
LS 270 A 941 φ D+0.5 MAX. P±0.5
Series
Lot. No.
L+0.5MAX.
φd 15MIN
4MIN
(mm)
Size φ6.3 × 9L φ6.3 × 10.5L φ8 × 7L φ8 × 9L φ8 × 12L φ10 × 13L
φD 6.3 6.3 8.0 8.0 8.0 10.0 Voltage
L
8.5 10.0 6.5
8.5 11.5 12.5
P 2.5 2.5 3.5 3.5 3.5 5.0
φd 0.6 0.5 0.6 0.6 0.6 0.6
V 2.5 4 6.3 10 16 Code e g j A C
Please refer to page 20 about the end seal configulation.
Size code Configuration Capacitance toleranc (±20%) Rated capacitance (270µF) Rated voltage (10V) Series name
Type
Dimension table in next page.
CAT.8100Z
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LSseries
Standard Ratings
Rated Voltage (V) code
Surge Voltage (V)
Rated Capacitance (µF)
2.5 (0E)
2.8
4 (0G)
4.6
6.3 (0J)
7.2
10 (1A)
11.5
16 (1C)
18.4
330 680 820 820 820 1500 270 560 560 680 1200 330 390 470 560 560 820 150 270 470 100 270 330 470
Case Size φD × L (mm)
6.3 × 9 8×7
6.3 × 9 8×9 8 × 12
10 × 13 6.3 × 9
8×7 8×9 8 × 12 10 × 13 6.3 × 10.5 8×7 8 × 12 6.3 × 9 8×9 10 × 13 6.3 × 10.5 8 × 12 10 × 13 6.3 × 10.5 8 × 12 10 × 13 10 × 13
tan δ
0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08
Leakage Current ESR (mΩ)
Rated Ripple
(µA)
(at 100kHz 20°C)
(mArms)
Part Number
500 340 500 410 410 750 500 448 448 544 960 416 491 592 706 706 1033 300 540 940 320 864 1056 1504
8
4800
PLS0E331MCO8
15
3900
PLS0E681MC L 2
8
4800
PLS0E821MCO8
7
5200
PLS0E821MCO6
7
5800
PLS0E821MDO1
8
5500
PLS0E152MDO1
8
4800
PLS0G271MCO8
15
3900
PLS0G561MC L 2
7
5200
PLS0G561MCO6
7
5800
PLS0G681MDO1
8
5500
PLS0G122MDO1
20
3000
PLS0J331MDL4
15
3900
PLS0J391MCL2
7
5500
PLS0J471MDO1
9
4300
PLS0J561MCO8
8
5000
PLS0J561MCO6
8
5500
PLS0J821MDO1
20
3000
PLS1A151MDL4
8
4900
PLS1A271MDO1
8
5500
PLS1A471MDO1
24
2800
PLS1C101MDL4
9
4500
PLS1C271MDO1
9
4700
PLS1C331MDO1
9
4700
PLS1C471MDO1
Rated ripple current (mArms) at 105°C 100kHz
Taping specifications are given in page 20, 21, 22. Please refer to page 3 for the minimum order quant.