DatasheetsPDF.com

PCJ0E272MCL1GS Dataheets PDF



Part Number PCJ0E272MCL1GS
Manufacturers Nichicon
Logo Nichicon
Description CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Datasheet PCJ0E272MCL1GS DatasheetPCJ0E272MCL1GS Datasheet (PDF)

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CJ Chip Type, Low ESR, Higher Capacitance series CK Low ESR, Higher Capacitance, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC). Low ESR CJ Specifications Low ESR Higher Capacitance, CF Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 2.5 to 16V Rated C.

  PCJ0E272MCL1GS   PCJ0E272MCL1GS


Document
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CJ Chip Type, Low ESR, Higher Capacitance series CK Low ESR, Higher Capacitance, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC). Low ESR CJ Specifications Low ESR Higher Capacitance, CF Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 2.5 to 16V Rated Capacitance Range 33 to 2700µF Capacitance Tolerance ± 20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C 1.25 Z– 55°C / Z+20°C 1.25 (100kHz) Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Resistance to Soldering Heat Marking After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In the case of peak temp, less than 250°C, reflow soldering shall be two times maximum. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Navy blue print on the case top Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions Capacitance Lot No. Plastic platform 0.3 MAX. C±0.2 Positive 0.5 MAX. E A ± 0.2 B± 0.2 CJ 220 j 841 φD + 0.5 MAX. Series Voltage ( j:6.3v) L +0.1 - 0.4 Negative H Type numbering system (Example : 6.3V 220µF) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PC J 0 J 2 2 1 MC L 1 GS Taping code Size code Configuration Capacitance toleranc (±20%) Rated capacitance (220µF) Rated voltage (6.3V) Series name Type (mm) Size φ5 × 6L φ6.3 × 6L φ6.3 × 8L φ8 × 7L φ8 × 8L φ8 × 10L φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 12.7L φD 5.0 6.3 6.3 8.0 8.0 8.0 8.0 10.0 10.0 10.0 L 5.9 5.9 7.9 6.9 7.9 9.9 11.9 7.9 9.9 12.6 A 6.0 7.3 7.3 9.0 9.0 9.0 9.0 11.0 11.0 11.0 B 5.3 6.6 6.6 8.3 8.3 8.3 8.3 10.3 10.3 10.3 Voltage C 5.3 6.6 6.6 8.3 8.3 8.3 8.3 10.3 10.3 10.3 E 1.6 2.1 2.1 3.2 3.2 3.2 3.2 4.6 4.6 4.6 H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 V 2.5 4 6.3 10 16 Code e g j A C Dimension table in next page. CAT.8100Z CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CJ series Standard Ratings Rated Voltage (V)(code) 2.5 (0E) 4 (0G) 6.3 (0J) 10 (1A) 16 (1C) Surge Voltage (V) 2.8 4.6 7.2 11.5 18.4 Rated Capacitance (µF) 180 390 470 560 560 680 820 820 1000 1200 1500 1500 2200 2700 100 150 270 330 390 470 560 560 680 1000 1000 1200 1200 1500 1500 1800 1800 2200 100 120 220 270 330 330 390 470 820 820 820 1200 1500 1500 1800 47 56 68 120 150 220 270 330 390 470 680 33 39 68 82 100 100 120 150 180 220 220 270 330 Case Size φD × L (mm) 5×6 6.3 × 6 6.3 × 8 6.3 × 8 8×7 8×7 8×8 8 × 12 8×8 10 × 8 8 × 10 8 × 12 10 × 10 10 × 12.7 5×6 5×6 6.3 × 6 6.3 × 6 6.3 × 8 8×7 8×7 8 × 12 8×8 8 × 10 10 × 8 8 × 12 10 × 10 8 × 12 10 × 10 10 × 10 10 × 12.7 10 × 12.7 5×6 5×6 6.3 × 6 6.3 × 8 6.3 × 8 8×7 8×7 8×8 8 × 10 8 × 12 10 × 8 10 × 10 10 × 10 10 × 12.7 10 × 12.7 5×6 .


PCJ0E222MCL1GS PCJ0E272MCL1GS PCJ0G101MCL1GS


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)