DatasheetsPDF.com

PCK0J821MCO1GS Dataheets PDF



Part Number PCK0J821MCO1GS
Manufacturers Nichicon
Logo Nichicon
Description CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Datasheet PCK0J821MCO1GS DatasheetPCK0J821MCO1GS Datasheet (PDF)

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CK Chip Type, Ultra-low ESR series Ultra-low ESR, Higher Capacitance, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC). CJ Low ESR CK Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 2.5 to 6.3V Rated Capacitance Range 220 to 2200µF Capacita.

  PCK0J821MCO1GS   PCK0J821MCO1GS


Document
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CK Chip Type, Ultra-low ESR series Ultra-low ESR, Higher Capacitance, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC). CJ Low ESR CK Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 2.5 to 6.3V Rated Capacitance Range 220 to 2200µF Capacitance Tolerance ± 20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C 1.25 Z– 55°C / Z+20°C 1.25 (100kHz) Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Resistance to Soldering Heat Marking After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In the case of peak temp, less than 250°C, reflow soldering shall be two times maximum. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Navy blue print on the case top Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions Capacitance Lot No. Plastic platform 0.3 MAX. C±0.2 Positive Type numbering system (Example : 6.3V 220µF) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PCK 0 J 2 2 1 MCO 1 GS 0.5 MAX. CK 220 j 941 φD + 0.5 MAX. Series Voltage ( j:6.3v) L +0.1 - 0.4 Negative H (mm) Size φ6.3 × 6L φ8 × 7L φ10 × 8L φ10 × 10L φD 6.3 8.0 10.0 10.0 L 5.9 6.9 7.9 9.9 A 7.3 9.0 11.0 11.0 B 6.6 8.3 10.3 10.3 Voltage C 6.6 8.3 10.3 10.3 E 2.1 3.2 4.6 4.6 H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 V 2.5 4 6.3 Code e g j B± 0.2 E A ± 0.2 Taping code Configuration Capacitance toleranc (±20%) Rated capacitance (220µF) Rated voltage (6.3V) Series name Type Dimension table in next page. CAT.8100Z CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CKseries Standard Ratings Rated Voltage Surge Voltage Rated Capacitance (V)(code) (V) (µF) 390 2.5 (0E) 2.8 560 680 1200 2200 330 4 (0G) 4.6 470 560 1000 1800 220 6.3 (0J) 7.2 330 390 820 1500 Case Size φD × L (mm) 6.3 × 6 8×7 8×7 10 × 8 10 × 10 6.3 × 6 8×7 8×7 10 × 8 10 × 10 6.3 × 6 8×7 8×7 10 × 8 10 × 10 tan δ 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 Leakage Current ESR (mΩ) (µA) (at 100kHz 20°C) 293 10 420 9 510 9 900 9 1650 8 396 10 564 9 672 9 1200 9 2160 8 416 10 624 9 737 9 1550 9 2835 8 Rated Ripple (mArms) 3900 4500 4500 5000 6000 3900 4500 4500 5000 6000 3900 4500 4500 5000 6000 Part Number PCK0E391MCO1GS PCK0E561MCO1GS PCK0E681MCO1GS PCK0E122MCO1GS PCK0E222MCO1GS PCK0G331MCO1GS PCK0G471MCO1GS PCK0G561MCO1GS PCK0G102MCO1GS PCK0G182MCO1GS PCK0J221MCO1GS PCK0J331MCO1GS PCK0J391MCO1GS PCK0J821MCO1GS PCK0J152MCO1GS Rated ripple current (mArms) at 105°C 100kHz No marked, 1 will be put at 12th digit of type numbering system. Taping specifications are given in page 23. Recommended land size, soldering by reflow are giv.


PCK0J391MCO1GS PCK0J821MCO1GS PCK0J152MCO1GS


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)