DatasheetsPDF.com

GP1U58Y Dataheets PDF



Part Number GP1U58Y
Manufacturers Sharp Electrionic Components
Logo Sharp Electrionic Components
Description IR Detecting Unit For Remote Control
Datasheet GP1U58Y DatasheetGP1U58Y Datasheet (PDF)

GP1U58Y Series GP1U58Y Series s Features 1. Less sensitive to a fluorescent lamp driven by inverter 2. Various B.P.F. ( Band Pass Filter ) frequency 3. Built-in voltage regulator circuit IR Detecting Unit For Remote Control s Outline Dimensions ( Unit : mm ) 15 g1 7.5 g1 3.65 13.25 Rib 1 Vout 2 Vcc 3 GND 12 3 14.2 1.4 s Applications 1. TVs 2. VCRs 3. Audio equipment 4. Air conditioners 5. CATV set top boxes 6. BS receivers 7. Multi-media equipments 2 15.4 + 0.5 0.3 3.6 3- 2.4 g2 2.54 2.

  GP1U58Y   GP1U58Y



Document
GP1U58Y Series GP1U58Y Series s Features 1. Less sensitive to a fluorescent lamp driven by inverter 2. Various B.P.F. ( Band Pass Filter ) frequency 3. Built-in voltage regulator circuit IR Detecting Unit For Remote Control s Outline Dimensions ( Unit : mm ) 15 g1 7.5 g1 3.65 13.25 Rib 1 Vout 2 Vcc 3 GND 12 3 14.2 1.4 s Applications 1. TVs 2. VCRs 3. Audio equipment 4. Air conditioners 5. CATV set top boxes 6. BS receivers 7. Multi-media equipments 2 15.4 + 0.5 0.3 3.6 3- 2.4 g2 2.54 2.54 2.54 g2 5.5± 0.5 1.7 g2 2.54 g2 2.1 Recommended drilling as viewed from the soldering face. * Tolerance :± 0.3mm g 1 Detector center g 2 The dimension of connector base s Absolute Maximum Ratings Parameter Supply voltage *1 Operating temperature Storage temperature *2 Soldering temperature *1 No dew formation *2 For 5 seconds ( Ta = 25˚C ) Rating 0 to 6.3 - 10 to + 70 - 20 to + 70 260 Unit V ˚C ˚C ˚C Symbol V CC T opr T stg T sol s Recommended Operating Conditions Parameter Supply voltage Symbol V CC Value 4.7 to 5.3 Unit V “ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device. ” 4.3 φ 0. 8 1 2 3 GP1U58Y Series s Electrical Characteristics Parameter Dissipation current High level output voltage Low level output voltage High level pulse width Low level pulse width B.P.F. center frequency Symbol I CC V OH V OL T1 T2 fO Conditions No input light MIN. V CC - 0.5 400 400 - ( Ta = 25˚C, VCC = + 5V) TYP. *4 40 MAX. 5.0 0.45 800 800 Unit mA V V µs kHz *3 - *3 The burst wave as shown in the following figure shall be transmitted by the transmitter shown in Fig. 1. *4 Diversified models with a different B.P.F frequency, as shown in a separate table, are also available. 600 µ s 600 µ s The value of fO is shown in a separate table. Duty 50% s Model Line-up Model No. GP1U58Y GP1U580Y GP1U581Y GP1U582Y GP1U583Y GP1U587Y B.P.F. frequency 40 36 38 36.7 32.75 56.8 Unit kHz s Internal Block Diagram Vout Amp Limiter B.P.F. Demodulator Integrator Comparator Vcc GND GP1U58Y Series s Performance Using the transmitter shown in Fig. 1, the output signal of the light detecting unit is good enough to meet the following items in the standard optical system in Fig. 2. ( 1 ) Linear reception distance characteristics When L= 0.2 to 8m, Ee<10 lx and φ = 0˚ in Fig. 2, the output signal shall meet the electrical characteristcs in the attached list. ( 2 ) Sensitivity angle reception distance characteristics When L= 0.2 to 6m, Ee< 10 lx and φ <= 30˚ in Fig. 2, the output signal shall meet the electrical characteristics in the attached list. ( 3 ) Anti outer peripheral light reception distance characteristics When L= 0.2 to 4m, Ee<=300 lx and φ = 0˚ in Fig. 2, the output signal shall meet the electrical characteristics in the attached list. 20cm PD49PI 10k Ω + 5V 10 µ F Transmitter (GL521 used ) Duty 50 % Center frequency (fo ) depends on the attached model list. 10k Ω Vout Oscilloscope Fig. 1. Transmitter In the above figure, the transmitter should be set so that the output V out can be 40mV PP . However, the PD49PI to be used here should be of the short-circuit current I SC = 2.6 µ A at E V = 100 lx. (E V is an illuminance by CIE standard light source A ( tungsten lamp ) . ) Light detector face illuminance : Ee φ φ Vout Reception distance : L Transmitter ( φ indicates horizontal and vertical directions. ) Fig. 2. Standard optical system GP1U58Y Series s Precautions for Use ( 1 ) Use the light emitting unit ( remote control transmitter ) , in consideration of performance, characteristics and operating condition of light emitting device and the characteristics of the light detecting unit. ( 2 ) Pay attention to a malfunction of the light detecting unit when the surface is stained with dust and refuse. Care must be taken not to touch the light detector surface. If it should be dirty, wipe off with soft cloth so as to prevent scratch. In case some solvents are required, use metyl alcohol, ethyl alcohol or isoprophyl alcohol. Also, protect the light detecting unit against flux and others. ( 3 ) The shield case shall be grounded on PWB pattern. ( 4 ) Do not apply unnecessary force to the terminals and case form outside. ( 5 ) Do not push the light detector surface ( photodiode ) from outside. ( 6 ) To avoid the electorstatic breakdown of IC, handle the unit under the condition of grounding with human body, soldering iron, etc. ( 7 ) In case of adopting the infrared light detecting unit for the wireless remote control, use it in accordance with the transmission scheme and the signal format recommended in “ Countermeasures for malfunction prevention of home appliances with infrared remote control” issued form Japan Association of Electrical Home Appliances ( A.


GP1U58X GP1U58Y GP1U77R


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)