SERVICE MANUAL. HD-EP10 Datasheet

HD-EP10 MANUAL. Datasheet pdf. Equivalent

HD-EP10 Datasheet
Recommendation HD-EP10 Datasheet
Part HD-EP10
Description HD DVD PLAYER SERVICE MANUAL
Feature HD-EP10; SERVICE MANUAL FILE NO. 810-200751GR HD DVD PLAYER HD-EP10 The above models are classified as gre.
Manufacture Toshiba
Datasheet
Download HD-EP10 Datasheet




Toshiba HD-EP10
SERVICE MANUAL
FILE NO. 810-200751GR
HD DVD PLAYER
HD-EP10
The above models are classified as green products (*1), as indicated by the underlined serial numbers.
This Service Manual describes replacement parts for the green products. When repairing these green
product(s), use the part(s) described in this manual and lead-free solder (*2).
For (*1) and (*2), see the next page.
Apr., 2007 GREEN



Toshiba HD-EP10
(*1) GREEN PRODUCT PROCUREMENT
The EC is actively promoting the WEEE & RoHS Directives that define standards for recycling
and reuse of Waste Electrical and Electronic Equipment and for the Restriction of the use of
certain Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any market-
ing of new products containing the restricted substances.
Increasing attention is given to issues related to the global environmental. Toshiba Corporation
recognizes environmental protection as a key management tasks, and is doing its utmost to
enhance and improve the quality and scope of its environmental activities. In line with this,
Toshiba proactively promotes Green Procurement, and seeks to purchase and use products,
parts and materials that have low environmental impacts.
Green procurement of parts is not only confined to manufacture. The same green parts used in
manufacture must also be used as replacement parts.
(*2) LEAD-FREE SOLDER
This product is manufactured using lead-free solder as a part of a movement within the con-
sumer products industry at large to be environmentally responsible. Lead-free solder must be
used in the servicing and repair of this product.
WARNING
This product is manufactured using lead free solder.
DO NOT USE LEAD BASED SOLDER TO REPAIR THIS PRODUCT !
The melting temperature of lead-free solder is higher than that of leaded solder by 86°F to
104°F (30°C to 40°C). Use of a soldering iron designed for lead-based solders to repair product
made with lead-free solder may result in damage to the component and or PCB being soldered.
Great care should be made to ensure high-quality soldering when servicing this product espe-
cially when soldering large components, through-hole pins, and on PCBs as the level of heat
required to melt lead-free solder is high.



Toshiba HD-EP10
SAFETY INSTRUCTIONS
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE ͳSAFETY PRECAUTIONͳ
AND ͳPRODUCT SAFETY NOTICEͳINSTRUCTIONS BELOW.
SAFETY PRECAUTION
WARNING: SERVICE SHOULD NOT BE ATTEMPTED BY ANYONE UNFAMILIAR WITH THE NECESSARY
PRECAUTIONS ON THIS RECEIVER. THE FOLLOWING ARE THE NECESSARY PRECAUTIONS TO BE
OBSERVED BEFORE SERVICING THIS CHASSIS.
An isolation transformer should be connected in the power line between the product and the AC line before any service
is performed on the product.
When replacing a chassis in the cabinet, always be certain that all the protective devices are put back in place, such as;
nonmetallic control knobs, insulating covers, shields, isolation resistor-capacitor network etc.
Always advise users to keep children away. There is danger of injury to children from tools, disassembled products, etc.
Always disconnect the power plug before starting work whenever power is not required. Failure to disconnect the power
plug before starting work can result in electrical shock.
Depending on the model, use an insulation transformer or wear gloves when servicing with the power on, and disconnect
the power plug to avoid electrical shock when replacing parts. In some cases, alternating current is also impressed in
the chassis, so electrical shock is possible if the chassis is contacted with the power on.
Always use the replacement parts specified for the particular model when making repairs. The parts used in products
have the necessary safety characteristics such as inflammability, voltage resistance, etc. ; therefore, use only
replacement parts that have these same characteristics. Use only the
specified parts when the mark is
include in a circuit diagram or parts list.
Parts mounting and routing of the wiring should be the same as that used originally. For safety purposes, insulating materials
such as tubing or tape is sometimes used and printed circuit boards are sometimes mounted floating. Also make sure that
wiring is routed and clamped to avoid parts that generate heat and which use high voltage. Always follow the original scheme.
After a repair has been completed, reassemble all disassembled pars, and route and reconnect the wiring, in accordance with
the original scheme. Do not allow internal wiring to be pinched by cabinets, panels, etc. Any error in reassembly or wiring
can result in electrical leakage, flame, etc.,and may be hazardous.
Never remodel the product in any way. Remodeling can result in improper operation, malfunction, or electrical leakage and
flame, which may be hazardous.







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)