LCD Module. LK520D3LB1S Datasheet

LK520D3LB1S Module. Datasheet pdf. Equivalent

LK520D3LB1S Datasheet
Recommendation LK520D3LB1S Datasheet
Part LK520D3LB1S
Description TFT LCD Module
Feature LK520D3LB1S; RECORDS OF REVISION MODEL No. : LK520D3LB1S SPEC No. : LD-K21Y19 SPEC No. DATE REVISED PAGE No. .
Manufacture Sharp
Datasheet
Download LK520D3LB1S Datasheet




Sharp LK520D3LB1S
RECORDS OF REVISION
MODEL No. : LK520D3LB1S
SPEC No. : LD-K21Y19
SPEC No.
DATE
REVISED
PAGE
No.
SUMMARY
LD-K21Y19 2009.12.14
-
-
-
NOTE
1st ISSUE



Sharp LK520D3LB1S
1. Application
This specification applies to the color 52.0” TFT-LCD module LK520D3LB1S.
LD-K21Y19-1
* This specification is proprietary products of SHARP CORPORATION (“SHARP”) and includes materials protected
under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any
means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of
SHARP.
* In case of using the device for applications such as control and safety equipment for transportation (aircraft, trains,
automobiles, etc.), rescue and security equipment and various safety related equipment which require higher
reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant
system design should be taken.
* Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications,
telecommunication equipment (trunk lines), nuclear power control equipment and medical or other equipment for
life support.
* SHARP assumes no responsibility for any damage resulting from the use of the device that does not comply with
the instructions and the precautions specified in these specification.
* Contact and consult with a SHARP sales representative for any questions about this device.
2. Overview
This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is
composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit, LED drive circuit and back
light system etc. Graphics and texts can be displayed on a 1920 RGB 1080 dots panel with one billion colors by
using 10bit LVDS (Low Voltage Differential Signaling) to interface, +12V of DC supply voltages.
This module also includes the LED-PWB to drive the LED. ( 120mA of DC supply current)
And in order to improve the response time of LCD, this module applies the Over Shoot driving (O/S driving)
technology for the control circuit .In the O/S driving technology, signals are being applied to the Liquid Crystal
according to a pre-fixed process as an image signal of the present frame when a difference is found between image
signal of the previous frame and that of the current frame after comparing them.
With this technology, image signals can be set so that liquid crystal response completes within one frame. As a
result, motion blur reduces and clearer display performance can be realized.
This LCD module also adopts Double Frame Rate driving method including FRC (Frame Rate Control) function
on the control circuit. Therefore the input signal to this LCD module is Single Frame Rate, but the output is
Double-Frame Rate picture (inserting the intermediate image which is generated by the FRC).
With combination of these technologies, motion blur can be reduced and clearer display performance can be
realized.
3. Mechanical Specifications
Parameter
Specifications
Display size
132.174 (Diagonal)
52.0 Diagonal
Active area
1152(H) x 648 (V)
Pixel Format
1920(H) x 1080(V)
1pixel = R + G + B dot
Pixel pitch
0.600(H) x 0.600 (V)
Pixel configuration
R, G, B vertical stripe
Display mode
Normally black
Unit Outline Dimensions (*1)
1227 (W) x 741 (H) x 27.6(D)
Mass
14.5
Surface treatment
Anti glare (Haze 7.3)
Hard coating: 3H
(*1) Outline dimensions are shown in Fig.17 (excluding protruding portion)
Unit
cm
inch
mm
pixel
mm
mm
kg



Sharp LK520D3LB1S
LD-K21Y19-2
4. Input Terminals
4.1. TFT panel driving
CN1 (Interface signals and +12V DC power supply) (Shown in Fig.1)
Using connector
: FI-RNE51SZ-HF (Japan Aviation Electronics Ind., Ltd.)
Mating connector
: FI-RE51HL, FI-RE51CL (Japan Aviation Electronics Ind., Ltd.)
Mating LVDS transmitter
: THC63LVD1023 or equivalent device
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Symbol
Function
VCC
+12V Power Supply
VCC
+12V Power Supply
VCC
+12V Power Supply
VCC
+12V Power Supply
VCC
+12V Power Supply
OPEN
GND
GND
GND
AIN0- Aport (-)LVDS CH0 differential data input
AIN0+ Aport (+)LVDS CH0 differential data input
AIN1- Aport (-)LVDS CH1 differential data input
AIN1+ Aport (+)LVDS CH1 differential data input
AIN2- Aport (-)LVDS CH2 differential data input
AIN2+ Aport (+)LVDS CH2 differential data input
GND
ACK- Aport LVDS Clock signal(-)
ACK+ Aport LVDS Clock signal(+)
GND
AIN3- Aport (-)LVDS CH3 differential data input
AIN3+ Aport (+)LVDS CH3 differential data input
AIN4- Aport (-)LVDS CH4 differential data input
AIN4+ Aport (+)LVDS CH4 differential data input
GND
BIN0- Bport (-)LVDS CH0 differential data input
BIN0+ Bport (+)LVDS CH0 differential data input
BIN1- Bport (-)LVDS CH1 differential data input
BIN1+ Bport (+)LVDS CH1 differential data input
BIN2- Bport (-)LVDS CH2 differential data input
BIN2+ Bport (+)LVDS CH2 differential data input
GND
BCK- Bport LVDS Clock signal(-)
BCK+ Bport LVDS Clock signal(+)
GND
BIN3- Bport (-)LVDS CH3 differential data input
BIN3+ Bport (+)LVDS CH3 differential data input
BIN4- Bport (-)LVDS CH4 differential data input
BIN4+ Bport (+)LVDS CH4 differential data input
GND
I2C_SCL I2C CLK
I2C_SDA I2C Data
Open
B_INT I2C bus enable (H:enable, L:disable) [Note 1]
PANEL_SEL (PANEL Sel Signal) [Note 2]
FRC_PWR_CTRL Power on sequence(DC/DC On Signal)
Remark
Open
Pull down : (GND)
Pull down : (GND)







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)