DatasheetsPDF.com

AS8222 Dataheets PDF



Part Number AS8222
Manufacturers ams
Logo ams
Description Enhanced FlexRay Standard Transceiver
Datasheet AS8222 DatasheetAS8222 Datasheet (PDF)

AS8222 Enhanced FlexRay Standard Transceiver 1 General Description The AS8222 is a high-speed fault tolerant device operating as interface between a generic FlexRay Communication Controller and the copper wiring. This device is the first FlexRay certified Transceiver for temperature ranges up to 150°C ambient temperature. For bare-die deliveries please contact ams for more information. The AS8222 is designed to extend the application range for high speed and safety critical time triggered bus s.

  AS8222   AS8222



Document
AS8222 Enhanced FlexRay Standard Transceiver 1 General Description The AS8222 is a high-speed fault tolerant device operating as interface between a generic FlexRay Communication Controller and the copper wiring. This device is the first FlexRay certified Transceiver for temperature ranges up to 150°C ambient temperature. For bare-die deliveries please contact ams for more information. The AS8222 is designed to extend the application range for high speed and safety critical time triggered bus systems in an automotive environment. The bus driver is protected against short circuits to the supply and GND. The AS8222 operates at baudrates up to 10 Mbps and is fully conforming to the FlexRay Electrical Physical Layer Specification V2.1 Rev B. The AS8222 provides a host controller interface consisting of Enable (EN) and Standby (STBN) input pins for mode handling by the microcontroller and the Error (ERRN) output pin, signalling failures and status information. The device supports the NORMAL mode with activated FlexRay bus transmitter and receiver, the RECEIVE_ONLY mode with activated receiver only to avoid unwanted disturbances while listening to the communication and the low-power modes STANDBY and SLEEP with very low power consumption. In case of undervoltage at one of the supply voltages (VBAT, VCC, and VIO) the device will change its mode to a low-power mode (either STANDBY or SLEEP mode) and the device will signal an error accordingly. In case of low voltage is detected on both VBAT and VCC the device will enter the POWER-OFF mode. Ensuring application in safety critical environments a two wire busguardian interface is implemented where additional redundant circuitries on the electronic-control-unit can monitor the communication on the receive enable output (RxEN) and can activate and deactivate through the bus guardian enable input (BGE) the transmitter. Additionally in low-power modes the wake conditions at the RxEN pin can be monitored. A thermal sensor circuit with an integral shutdown mechanism prevents damage to the device in extreme temperature conditions. 2 Key Features Data transfer up to 10 Mbps Compliant with FlexRay Electrical Physical Layer Specification V2.1 Rev. B Wide operating ambient temperature range -40°C to +150°C Excellent EMC performance High common mode range insures excellent EMI immunity Interface with optional bus guardian for bus supervision Automatic thermal shutdown protection Supports 12, 24V systems with low sleep current consumption Integrated power management system Two INH pins for the external voltage regulators control Local wake-up input Remote wake-up capability via FlexRay bus in sleep mode Supports 2.5, 3, 3.3, 5 V microcontrollers and automatically adapts to interface levels Does not disturb the bus line if not powered Protected against damage due to short circuit conditions on the bus (positive and negative battery voltage) Small Pb-free package: SSOP-20 Automotive qualified to AEC-Q100, grade 0 For bare-die deliveries please contact us. 3 Applications The AS8222 FlexRay Standard Transceiver is best fitting for automotive FlexRay nodes where bus wake-up and voltage regulator control for voltage supplies is needed. The device addresses all ECUs connected to the permanent battery supply (terminal 30). The device is best suited for high temperature applications with up to 150°C. www.ams.com/eng/FlexRay/AS8222 Revision 1.0 1 - 42 AS8222 Datasheet - Applications Figure 1. AS8222 Enhanced FlexRay Standard Transceiver Block Diagram STBN EN ERRN RxD TxD TxEN BGE RxEN INH1 INH2 VIO AS8222 Host Controller Interface VIO Communication Controller Interface Digital Logic VBAT VBAT Bus Guardian Interface Power Supply Interface Bus Failure Detector Transmitter Receiver Wake-Up Detector BP BM VBAT VIO VCC GND WAKE www.ams.com/eng/FlexRay/AS8222 Revision 1.0 2 - 42 AS8222 Datasheet - Contents Contents 1 General Description .................................................................................................................................................................. 1 2 Key Features............................................................................................................................................................................ 1 3 Applications............................................................................................................................................................................... 1 4 Pin Assignments ....................................................................................................................................................................... 5 4.1 Pin Descriptions.................................................................................................................................................................................... 5 5 Absolute Maximum Ratings ...........................................................


AS1750 AS8222 AS8515


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)