Document
www.DataSheet4U.com
AS Series • Current Sense Inductors & Transformers
AS Series Current Sensors are designed as a low cost method of controlling, monitoring or measuring AC currents. The sensors serve as feedback elements between the output and pulse control circuitry providing accurate regulation of switch mode power supplies.
Features • Fully encapsulated for optimal PC board mounting • Frequency range from 20kHz to 200kHz • Primary current rating to 15 Amps • Primary to secondary isolated to 2500 VAC • Meets VDE norms • Optimum performance over designated current and
frequency range • Competitive pricing due to high volume production • Manufactured in ISO-9001 approved facility
Applications
Isolated current feed-back signal in Switch Mode Power Supplies • Motor current load/overload • Lighting • Switch Controls Ultra-sound
current • High resolution sonar current •
Isolated bi-directional current sensor with full wave bridge rectifier
Electrical Specifications at 25°C
Part Number
AS-100 AS-101 AS-102 AS-103 AS-104 AS-105 AS-110 AS-111 AS-112 AS-113 AS-114 AS-115
Prim./Sec. Ratio
1:50 1:100 1:200 1:300 1:500 1:750 1:50CT 1:100CT 1:200CT 1:300CT 1:500CT 1:750CT
Lsec (1) (mH Min)
6 25 100 250 700 1682 6 25 100 250 700 1682
DCRsec (Ohms Max.)
Sec. Term. (2) Resistance
(Ohms Nom.)
0.6 50
1.1 100
4.5 200
D10a.t0aSheet4U.c3o0m0
25.0 500
43.0 750
0.3 / 0.3
25 + 25
0.55 / 0.55
50 + 50
2.25 / 2.25
100 + 100
5.0 / 5.0
150 + 150
12.5 / 12.5
250 + 250
21.5 / 21.5
375 + 375
Isec (3) Max.
300mA 150mA 75mA 50mA 30mA 40mA 300mA 150mA 75mA 50mA 30mA 40mA
Volt µS (4) Max.
175 350 700 900 1500 3750 175 350 700 900 1500 3750
Schematic
1
3 DataShee
1 2 3
Notes: 1) Lsec: Secondary inductance tested at 10kHz and 10mV for 1:50 through 1:500
Prim./Sec. ratios and 1kHz/10mV for Prim./Sec. ratio of 1:750
2) This nominal termination resistance value will yield approximately 1.0V
of output for each amp of current in a single turn sense line. The output
Voltage/Ampere of these devices can be increased or decreased linearly
over a restricted temperature range by adjusting the terminating resistance.
3) For Prim./Sec. Ratios of 1:50 through 1:500, the Isec value corresponds to a maximum primary current of 15 Amp-turns rms while the Isec value for the ratio of
1:750 corresponds to a max. primary current of 30 Amp-turns rms. 1
4) VµS = R t x Is x 2F Rt (Ohms): Recommended Terminating Resistance Is (A): Secondary Current F (Hz): Frequency
5) Operating Temperature Range: -40°C to +120°C
6) Pin 2 is on Center-Tapped (CT) versions only
17.2 (0.677)
17.0 (0.669)
0.60 Ø (0.024)
TALEMA
ASXXX 12 3
5.0 (0.197)
20.4 (0.803)
6.35 (0.250)
12.7 (0.500)
+
4 .0 (0.157)
9.53
(0.375) 1
23
+_
_
Primary Sense Current
DataSheet4U.com
THE TALEMA GROUP • World Wide Toroidal Specialists
(07-03) AS Series
DataSheet4 U .com
www.DataSheet4U.com
AS Series • Current -Sense Inductors & Transformers
Electrical Specifications at 25°C
Part Number
Type 1 AS-200 AS-201 AS-202 AS-210 AS-211 AS-212
Type 2 AS-300 AS-301 AS-302 AS-310 AS-311 AS-312 AS-320 AS-321 AS-322 AS-330 AS-331 AS-332
Prim./Sec. Ratio
1:50 1:100 1:200 1:50CT 1:100CT 1:200CT 1:50 1:100 1:200 1:50CT 1:100CT 1:200CT
Lsec (1) (mHMin.)
DCRsec (Ohms Max.)
Sec. Term. (2) Resistance (Ohms Nom.)
5 0.65
50
20 1.30
100
80 4.50
200
5 0.65 25 + 25
20 1.30 50 + 50
80
4.50
100 + 100
5 0.65
50
20 1.30
100
80 4.50
200
5 0.65 25 + 25
20 1.30 50 + 50
80
4.50
100 + 100
Isec (3) Volt µS (4)
Max.
Max.
Schematic
300mA
175
150mA 350 1
75mA 700 2
300mA
175
1
150mA
350
75mA 700 2
300mA 175 1
150mA 350 2
6
75mA 700 7
300mA 175 1
150mA
350
2 6
75mA 700 7
3
5 3 4 5 3
5 3 4 5
et4U.com
14.50 (0.571)
10.15 (0.400)
5.08 (0.200)
345
15.25 (0.600)
12
Type 1
18.0 (0.709)
19.60 (0.772)
4.0 (0.157)
17.8 (0.700)
12.7 (0.500)
6.35 (0.250)
Type 2
17.8 (0.700)
Pins 1 & 2 Ø 1.30 (0.051)
3 45
67
Pins 3, 4 &5
Ø 1.00D(0a.0ta39S) heet4U1.com 2
12.7 (0.500) 17.8 22.9
(0.700) (0.902)
4.0 (0.157)
Pins 1, 2, 6 & 7 Ø 1.30 (0.051) Pins 3, 4 &5 Ø 0.80 (0.032)
Features • Meets requirements of IEC 950 and VDE norms UL94, VO recognized materials • Operating frequency range from 20kHz to 200kHz
Electrical Specifications at 25°C
Part Number AS-400 AS-401 AS-402
AS-403
AS-404 AS-405 AS-406 AS-407
Pri./Sec. Ratio 1:100 1:100 1:100
1:100
1:100 1:500 1:500 1:500
IP
Volt µS Application Schematic
Amps (Max.)
Case Type
1 350 Switching 1
2 550 Switching 5 1500 Switching 2
7A
A 8B
1
10
1500
Switching
2 3
4
50 1500 Switching
50 2700 Switching
65 4200 Switching
80 7500 Switching
7
A
8
B 7A
8A
B
• Operating Temperature Range: -40°C to +120°C • Primary to secondary isolated to 4000 VAC • Primary current rating to 80 Amps
Dimensions CDE FGH 17.8 12.8 20.0 10.0 5.0 15.0 23.0 15.5 25.0 12.5 10.0 20.0 32.5 18.0 35.5 15.0 12.5 --
32.0 20.5 35.0 17.5 12.5 27.5
32.5 18.0 35.5 15.0 12.5 -23.0 15.5 25.0 12.5 10.0 20.0 27.0 18.0 30.0 15.0 12.5 22..