DatasheetsPDF.com

FM-6038LM-5CN Dataheets PDF



Part Number FM-6038LM-5CN
Manufacturers OPTO-SENSOR
Logo OPTO-SENSOR
Description IR Receiver
Datasheet FM-6038LM-5CN DatasheetFM-6038LM-5CN Datasheet (PDF)

FM-6038□□-5CN Series IR Receiver Modules for Remote Control Systems Description The FM-6038□□-5CN is a Bi-CMOS IC for use in infrared remote control system. Small-sized, light-weight, and low current consumption. modules have been achieved by using resin mold. The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the reliable function even in disturbed ambient and the protection against uncontrolled output pulses. Features ƒ Supply Voltage Range: 2.7V.

  FM-6038LM-5CN   FM-6038LM-5CN


Document
FM-6038□□-5CN Series IR Receiver Modules for Remote Control Systems Description The FM-6038□□-5CN is a Bi-CMOS IC for use in infrared remote control system. Small-sized, light-weight, and low current consumption. modules have been achieved by using resin mold. The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the reliable function even in disturbed ambient and the protection against uncontrolled output pulses. Features ƒ Supply Voltage Range: 2.7V to 6 V ƒ TTL and CMOS compatibility ƒ Photo detector and preamplifier in one package. ƒ Internal filter for PCM frequency ƒ Open collector output (built-in Pull-up resistor(40K)) ƒ Output active low ƒ Enhanced Immunity against all kinds of disturbance light ƒ No occurrence of disturbance pulses at output pin within nominal conditions. ƒ Short settling time after power On.( below 1msec) ƒ Meet RoHS Application Circuit Transmitter IR Receiver Module VCC VOUT IC 47~100Ω 47uf VCC MCU GND GND R-C filter recommended to suppress power supply disturbances. R-C filter should be connected closely between VCC pin and GND pin. Block Diagram B.P.F Center Frequency Model No. FM-6032□□-5CN FM-6036□□-5CN FM-6038□□-5CN FM-6040□□-5CN FM-6056□□-5CN Carrier Frequency (fo) 32 kHz 36 kHz 38 kHz 40 kHz 56 kHz Page 1 September 2011 Rev 1.2 www.opto-sensor.com.tw FM-6038□□-5CN Series Suitable Data Format NEC code ◆ Sony 15bit RC5 code ◆ Sony 20bit RC6 code ◆ RCMM code Sony 12 bit ◆ RCA code Note: ◆:Suitable for this IR code ;◇:Not recommended Absolute Maximum Ratings Parameter Supply Voltage Supply Current Operating Temperature Storage Temperature Soldering Temperature Symbol VCC ICC Topr Tstg Tsd ◆ RCS-80 code ◇ Sharp code ◇ High data rate code ◇ Disturbance suppression ◇ ◇ ◇ ◆ Ratings 6.5 3.0 -20 ~ +80 -30 ~ +85 260℃, Max 5 sec (Ta = 25℃) Unit V mA ℃ ℃ ℃ Electro-optical Characteristics Parameter Symbol Supply Current ICC Output Voltage Voh Vol Peak Wave Length λp Internal Pull-up Resistor Rpul BPF frequency fc ±0˚ Arrival Distance L ±30˚ ±45˚ Min. 0.7 Vcc-0.5 -3.5 15 10 7 Output Pulse width Tpw 400 Typ. 1 0.2 940 42 fo - 600 Max. 1.3 0.4 +3.5 - 800 Unit mA V V nm ㏀ % m m m us (Ta = 25℃) Conditions No signal No external pull-up resistor (Isink<1mA) Fig 1,2,3 Burst Wave =600us Period = 1.2ms Note : 1) Arrival Distance Effected by Environment 2) While the device is operational across the temperature range, functionality will vary with temperature. Specifications are stated only at 25°C unless otherwise noted. 3) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Page 2 September 2011 Rev 1.2 www.opto-sensor.com.tw FM-6038□□-5CN Series [ Fig.1 ] Data Signal diagram Data Word t Pause enlarge Carrier Frequency : fo t Burst t Gap (Output pulse) ƒ t Gap : Signal gap time between two burst in pulses of carrier. Minimum Gap Time ≧ 300us ƒ t Burst : Length of a burst in pulses of the carrier frequency. Minimum Burst ≧ 300us ƒ t pause : Data pause between two data words. Minimum Data PauseTime ≧ 20ms [ Fig.2 ] Transmitter S/Transmitter 30㎝ 10K PD 100uf 10K VCC VOUT GND ※ The specifications shall be satisfied under the following conditions. The standard transmitter shall be specified of the burst wave form adjusted to VOUT 200mVp-p upon Po measuring circuit Standard Transmitter [ Fig.3 ] Test condition of arrival distance Transmitter Vout osc GND Vcc : Indicates horizontal and vertical directions [ Measurement condition for arrival distance ] ☞ Ambient light source : Detecting surface illumination shall be irradiate 200±50Lux under ordinary white fluorescence lamp without high frequency lighting Page 3 September 2011 Rev 1.2 www.opto-sensor.com.tw FM-6038□□-5CN Series Supply Current(㎃) Relative responsiv ity Electrical/Optical Characteristics [ Fig.4 ] Supply Current vs. Voltage 2.5 2.0 1.5 1.0 0.5 0.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 Supply Voltage(V) [ Fig.6 ] BPF Fc Curve BPF fc 1.2 1 0.8 0.6 0.4 0.2 0 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 f/fo Relative Frequency ESD Test Results [ Fig.5 ] Relative Spectral Sensitivity vs. Wavelength Relative Radiant(˚) [ Fig.7 ] Directivity (Horizontal/Vertical) 0˚ 20˚ 40˚ 100 V 90 H 80 60 40 20 0 Relative Sensitivity(%) 60˚ 80˚ Parameter Conditions Specification Results Machine Model C=200㎊, R=0Ω Min ±200V >±200V Human Body C=100㎊, Model R=1.5㏀ Min ±2000V >±2000V Page 4 September 2011 Rev 1.2 www.opto-sensor.com.tw FM-6038□□-5CN Series FM-6038LM-5CN NOTE: 1N. OPITNEC:ONFIG. 1.1PINVouCtONFIG 2①GVNDout 3②VGccND 2. ③G.TVc±c0.3 (2U.NGIT.:Tm±m0) .3 (UNIT: mm) A3 FM-6038TM2-5CN NOTE.


Si5475DDC FM-6038LM-5CN FM-6038TM2-5CN


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)