Receiver Modules. FM-6038TF2-5CN Datasheet

FM-6038TF2-5CN Modules. Datasheet pdf. Equivalent

Part FM-6038TF2-5CN
Description IR Receiver Modules
Feature FM-6038□□-5CN Series IR Receiver Modules for Remote Control Systems Description The FM-6038□□-5CN.
Manufacture OPTO-SENSOR
Datasheet
Download FM-6038TF2-5CN Datasheet



FM-6038TF2-5CN
FM-6038□□-5CN Series
IR Receiver Modules for Remote Control Systems
Description
The FM-6038□□-5CN is a Bi-CMOS IC for use in infrared
remote control system.
Small-sized, light-weight, and low current consumption.
modules have been achieved by using resin mold.
The demodulated output signal can directly be decoded
by a microprocessor. The main benefit is the reliable
function even in disturbed ambient and the protection
against uncontrolled output pulses.
Features
ƒ Supply Voltage Range: 2.7V to 6 V
ƒ TTL and CMOS compatibility
ƒ Photo detector and preamplifier in one package.
ƒ Internal filter for PCM frequency
ƒ Open collector output (built-in Pull-up resistor(40K))
ƒ Output active low
ƒ Enhanced Immunity against all kinds of disturbance light
ƒ No occurrence of disturbance pulses at output pin within nominal conditions.
ƒ Short settling time after power On.( below 1msec)
ƒ Meet RoHS
Application Circuit
Transmitter
IR Receiver Module VCC
VOUT
47~100
47uf
VCC
MCU
GND GND
R-C filter recommended to suppress power supply disturbances.
R-C filter should be connected closely between VCC pin and GND pin.
Block Diagram
B.P.F Center Frequency
Model No.
FM-6032□□-5CN
FM-6036□□-5CN
FM-6038□□-5CN
FM-6040□□-5CN
FM-6056□□-5CN
Carrier Frequency (fo)
32 kHz
36 kHz
38 kHz
40 kHz
56 kHz
Page 1
光電企業有限公司
September 2011 Rev 1.2
www.opto-sensor.com.tw



FM-6038TF2-5CN
FM-6038□□-5CN Series
Suitable Data Format
NEC code
Sony 15bit
RC5 code
Sony 20bit
RC6 code
RCMM code
Sony 12 bit
RCA code
Note: ◆:Suitable for this IR code ;◇:Not recommended
Absolute Maximum Ratings
Parameter
Supply Voltage
Supply Current
Operating Temperature
Storage Temperature
Soldering Temperature
Symbol
VCC
ICC
Topr
Tstg
Tsd
RCS-80 code
Sharp code
High data rate code
Disturbance suppression
Ratings
6.5
3.0
-20 ~ +80
-30 ~ +85
260, Max 5 sec
(Ta = 25℃)
Unit
V
mA
Electro-optical Characteristics
Parameter
Symbol
Supply Current
ICC
Output Voltage
Voh
Vol
Peak Wave Length
λp
Internal Pull-up Resistor
Rpul
BPF frequency
fc
±0˚
Arrival Distance
L ±30˚
±45˚
Min.
0.7
Vcc-0.5
-
-
-
-3.5
15
10
7
Output Pulse width
Tpw 400
Typ.
1
-
0.2
940
42
fo
-
-
-
600
Max.
1.3
-
0.4
-
-
+3.5
-
-
-
800
Unit
mA
V
V
nm
%
m
m
m
us
(Ta = 25℃)
Conditions
No signal
No external
pull-up resistor
(Isink1mA)
Fig 1,2,3
Burst Wave =600us
Period = 1.2ms
Note :
1) Arrival Distance Effected by Environment
2) While the device is operational across the temperature range, functionality will vary with temperature.
Specifications are stated only at 25°C unless otherwise noted.
3) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated
under “recommended operating conditions” is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Page 2
光電企業有限公司
September 2011 Rev 1.2
www.opto-sensor.com.tw





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)