Document
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
PXENPCAPTM-
Series
・Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte.
(ESR and rated ripple current values are improved from PXA series.)
・Rated voltage range : 2.5 to 16Vdc, Capacitance range : 33 to 2,700µF ・Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
・Solvent resistant type (see PRECAUTIONS AND GUIDELINES) ・RoHS Compliant ・Halogen Free
◆SPECIFICATIONS
PXF P34 Lower ESR
PXE
Lower ESR PXA P38
Items
Characteristics
Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current Dissipation Factor (tan ) Low Temperature Characteristics (Max. Impedance Ratio) Endurance
-55 to +105℃
2.5 to 16Vdc ±20% (M) Rated voltage×1.15 Shall not exceed values shown in STANDARD RATINGS.
(at 20℃, 120Hz) (at 105℃)
(at 20℃ after 2 minutes)
0.12 max.
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)≦1.15 Z(-55℃)/Z(+20℃)≦1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Bias Humidity
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at
60℃, 90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Surge Voltage
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Failure Rate
Leakage current
≦The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
◆MARKING
●Terminal Code : A
W
0.3max. L±0.3 (Note)
A±0.2
(Note) L±0.5 for HA0, HC0, JA0, JC0
Size Code φD L A B C
W
E61 5 5.8 5.3 5.3 5.9 0.5 to 0.8
F61 6.3 5.8 6.6 6.6 7.2 0.5 to 0.8
F80 6.3 7.7 6.6 6.6 7.2 0.5 to 0.8
H70 8 6.7 8.3 8.3 9.0 0.7 to 1.1
H80 8 7.7 8.3 8.3 9.0 0.7 to 1.1
HA0 8 10.0 8.3 8.3 9.0 0.7 to 1.1
HC0 8 12.0 8.3 8.3 9.0 0.7 to 1.1
J80 10 7.7 10.3 10.3 11.0 0.7 to 1.1
JA0 10 10.0 10.3 10.3 11.0 0.7 to 1.1
JC0 10 12.2 10.3 10.3 11.0 0.7 to 1.1
P 1.4 1.9 1.9 3.1 3.1 3.1 3.1 4.5 4.5 4.5
EX) 2.5V390µF
E49A 390 2.5V
◆PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A PXE A RA M G
Supplement code Size code
Capacitance tolerance code Capacitance code (ex. 47µF:470,100µF:101)
Taping code Terminal code Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category Please refer to "Product code guide (conductive polymer type)"
φD±0.5 B±0.2 P C±0.2
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
36 CAT. No. E1001O
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
PXENPCAPTM-
Series
◆STANDARD RATINGS
WV (Vdc) 2.5
4
6.3
10 16
Cap (µF)
180 390 470 560 560 680 820 820 1,000 1,200 1,500 1,500 2,200 2,700 100 150 270 330 390 470 560 680 1,000 1,000 1,200 1,200 1,500 1,800 1,800 100 120 220 270 330 330 390 470 820 820 820 1,200 1,500 1,500
47 56 68 120 150 220 270 330 390 470 680 33 39 68 82 100 100 120 150 180 220 220 330
Size code
E61 F61 F80 F80 H70 H70 H80 HC0 H80 J80 HA0 HC0 JA0 JC0 E61 E61 F61 F61 F80 H70 H70 H80 HA0 J80 HC0 JA0 JA0 JA0 JC0 E61 E61 F61 F80 F80 H70 H70 H80 HA0 HC0 J80 JA0 JA0 JC0 E61 E61 E61 F61 F80 H70 H70 H80 HA0 J80 JA0 E61 E61 F61 F80 F80 H70 H70 H80 HA0 HA0 J80 JA0
Leakage current (µA max./after 2min.)
90.0 195 235 280 280 340 410 410 500 600 750 750 1,100 1,350
80.0 120 216 264 312 376 448 544 800 800 960 960 1,200 1,440 1,440 126 151 277 340 415 415 491 592 1,030 1,030 1,030 1,510 1,890 1,890
94.0 112 136 240 300 440 540 660 780 940 1,360 105 124 217 262 320 320 384 480 576 704 704 1,050
ESR
Rated ripple current
(m max./20 , 100k to 300kHz) (mArms/105 , 100kHz)
21 2,670 15 3,160 13 3,600 13 3,600 13 4,100 13 4,100 12 4,260
9 5,400 12 4,260 13 4,450 10 5,220
9 5,400 10 5,500
9 5,600 22 2,610 22 2,610 15 3,160 15 3,160 14 3,470 14 3.