Document
UNISONIC TECHNOLOGIES CO., LTD U74AHC1G06
INVERTER WITH OPEN-DRAIN OUTPUT
DESCRIPTION
The UTC U74AHC1G06 is an inverter with open-drain output and it provides the Function Y = A .
FEATURES.
* Operation Voltage Range: 2V~5.5V * High noise immunity * Low Power Dissipation
CMOS IC
ORDERING INFORMATION
Ordering Number U74AHC1G06G-AE5-R U74AHC1G06G-AL5-R
Package SOT-23-5 SOT-353
Packing Tape Reel Tape Reel
MARKING
www.unisonic.com.tw Copyright © 2015 Unisonic Technologies Co., Ltd
1 of 4
QW-R502-376.C
U74AHC1G06
PIN CONFIGURATION
FUNCTION TABLE
INPUT A
OUTPUT Y
HL
LZ
Note: H: High Voltage Level
L: Low Voltage Level
Z: High-Impedance OFF-State
LOGIC DIAGRAM
Logic symbol
CMOS IC
IEC logic symbol
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
2 of 4
QW-R502-376.C
U74AHC1G06
CMOS IC
ABSOLUTE MAXIMUM RATING (unless otherwise specified)
PARAMETER
SYMBOL
RATINGS
UNIT
Supply Voltage Input Voltage
VCC -0.5~+7.0 VIN -0.5~+7.0
V V
Input Clamp Current (VIN<-0.5V) Output Clamp Current (VOUT<-0.5V) (Note 2)
IIK IOK
-20 mA ±20 mA
Output Current (VOUT>-0.5V) VCC or GND Current
IOUT ±25 mA ICC ±75 mA
Power Dissipation Derate above Ta>87.5°C
PD
250 mW 4.0 mW/K
Operating Temperature Storage Temperature
TOPR TSTG
-40~+125 -65 ~ +150
°C °C
Notes: 1. Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
2. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
RECOMMENDED OPERATING COMDITIONS
PARAMETER
SYMBOL
CONDITIONS
MIN
Supply Voltage Input Voltage Output Voltage
Input Transition Rise or Fall Rate
VCC VIN VOUT
∆t/∆v
VCC=3.3+0.3V VCC=5.0+0.5V
2.0 0 0
STATIC CHARACTERISTICS (TA=25°C)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
High-Level Input Voltage
Low-Level Input Voltage
Low-Level Output Voltage
Input Leakage Current 3-state output OFF-state current Quiescent Supply Current Input Capacitance
VIH
VIL
VOL
II(LEAK) IOZ ICC CIN
VCC= 2.0V
VCC=3.0V
VCC=5.5V
VCC= 2.0V
VCC=3.0V
VCC=5.5V
VCC=2.0V
VCC=3.0V
IOL=50μA
VCC=4.5V
VCC=3.0V, IOL =4mA
VCC=4.5V, IOL =8mA
VCC=0~5.5V, VIN=VCC or GND
VCC=5.5V, VIN=VIH or VIL,
VOUT=VCC or GND
VCC=5.5V, VIN=VCC or GND,
IOUT=0A
VIN=VCC or GND
1.5 2.1 3.85
DYNAMIC CHARACTERISTICS (Input: tR, tF≤3ns; PRR≤1MHz, TA=25°C)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
Propagation delay from input (A)to output(Y)
tPZL tPLZ
VCC =3.3±0.3 V
CL=15 pF CL=50 pF CL=15 pF CL=50 pF
tPZL tPLZ
VCC =5±0.5 V
CL=15 pF CL=50 pF CL=15 pF CL=50 pF
TYP
MAX 5.5 5.5 VCC 100 20
UNIT V V V
ns/V ns/V
TYP MAX UNIT V V V
0.5 V 0.9 V 1.65 V 0.1 V 0.1 V 0.1 V 0.36 V 0.36 V ±0.1 μA
±0.25 μA
1.0 μA
1.5 10 pF
TYP MAX UNIT 3.7 7.0 ns 5.2 10.0 ns 4.8 6.4 ns 6.9 10.0 ns 2.7 4.9 ns 3.8 7.0 ns 3.0 4.1 ns 4.3 6.5 ns
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
3 of 4
QW-R502-376.C
U74AHC1G06
TEST CIRCUIT AND WAVEFORMS
TEST CIRCUIT Note: CL includes probe and jig capacitance.
CMOS IC
TEST tPLH/tPHL tPHZ/tPZH tPLZ/tPZL
S Open GND VCC
PROPAGATION DELAY TIMES
UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
4 of 4
QW-R502-376.C
.