Document
AZ DISPLAYS
SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY
CUSTOMER APPROVAL
※ PART NO. : ATM0500D14-T(AZ DISPLAYS) VER1.0
APPROVAL
COMPANY CHOP
CUSTOMER COMMENTS
AZ DISPLAYS ENGINEERING APPROVAL
DESIGNED BY
CHECKED BY
APPROVED BY
Herbert
ATM0500D14-T(AZ DISPLAYS)TFT MODULE V1.0
REVISION RECORD
REVISION REVISION DATE
PAGE
CONTENTS
VER1.0 2014-12-10
FIRST ISSUE
※ CONTENTS AZ DISPLAYS
1
ATM0500D14-T(AZ DISPLAYS)TFT MODULE V1.0
1. GENERAL SPECIFICATIONS 2. PIN ASSIGNMENT 3. OPERATING SPECIFICATIONS 4. OPTICAL SPECIFICATIONS 5. RELIABILITY TEST 6. PRECAUTION FOR USING LCM 7. MECHANICAL DRAWING 8. PACKAGE DRAWING 9. INSPECTION SPECIFICATION
AZ DISPLAYS
2
ATM0500D14-T(AZ DISPLAYS)TFT MODULE V1.0
1. GENERAL SPECIFICATIONS
Item 1. LCD size 2. Driver element 3. Resolution 4. Display mode 5. Dot Pitch (W*H) 6. Pixel pitch(W*H) 7. Active Area(W*H) 8. Module size (W*H) 9. Surface treatment 10. Color arrangement 11. Color 12. Interface 13. Weight 14. RoHS
Specification 5.0 inch(Diagonal) a-Si TFT active matrix 480x(RGB)x272 Normally white , Transmissive 0.693mm(W) x 0.231mm(H) 0.231mm(W) x 0.231mm(H) 110.88mm(W) x 62.83mm(H) 120.8mm(W) x 75.9mm(H) x4.3mm(Typ) Anti-glare RGB-stripe 262K 24bit RGB interface T.B.D. RoHS compliant
Remark Note 1
Note 1: Please refer to mechanical drawing.
AZ DISPLAYS
3
ATM0500D14-T(AZ DISPLAYS)TFT MODULE V1.0
2. PIN ASSIGNMENT
TFT LCD Panel Driving Section FPC Connector is used for the module electronics interface. The recommended model is
“FH19SC-40S-0.5SH" manufactured by Hirose.
Pin No. 1 2 3 4
5~12 13~20 21~28
29 30 31 32 33 34 35 36 37 38 39 40
Symbol VLEDVLED+ GND VDD R0~R7 G0~G7 B0~B7 GND CLK DISP HSYNC VSYNC
DE NC GND XR YD XL YU
Function Power for LED backlight(Cathode) Power for LED backlight(Anode)
Ground Power supply
Red data Green data Blue data
Ground Pixel clock Display On/Off Horizontal sync Vertical sync Data enable No connection
Ground Right electrode Bottom electrode Left electrode Top electrode
Level P P P P I I I P I I I I I -P -----
Note
I: input, O: output, P: Power
AZ DISPLAYS
4
ATM0500D14-T(AZ DISPLAYS)TFT MODULE V1.0
Tout Panel Section Pin No. Symbol
I/O
1 YU Top
2 XL Left
3 YD Bottom
4 XR Right
Function Top electrode – differential analog Left electrode – differential analog Bottom electrode – differential analog Right electrode – differential analog
Remark
AZ DISPLAYS
5
ATM0500D14-T(AZ DISPLAYS)TFT MODULE V1.0 3. Operating Specification
3.1.1 ABSOLUTE MAXIMUM RATINGS
Item
Symbol
Values Min. Max.
Unit
Remark
Power Voltage Operation Temperature Storage Temperature
LED Reverse Voltage
VDD
-0.5 5.0
V
TOP
-20 70
ºC
TST
-30 80
ºC
VR
-
1.2
V
Each LED Note 2
LED Forward Current
IF
25 mA Each LED
Note 1: The absolute maximum rating values of this product are not allowed to be exceeded
at any times. Should a module be used with any of the absolute maximum ratings exceeded, the characteristics of the module may not be recovered, or in an extreme case, the module may be permanently destroyed.
Note 2: VR Conditions: Zener Diode 20mA
3.1.2 Typical Operation Conditions
Item
Symbol
Min.
Values Typ.
Max.
Unit
Power Voltage
VDD
3.0 3.3 3.6
V
Input Logic High Voltage
VIH
0.7DVDD
--
DVDD
V
Input Logic Low Voltage
VIL
0 -- 0.3DVDD V
Note 1: VDD setting should match the signals output voltage of customer’s system board. Note 2: DCLK,HS,VS,RESET,DE,R0~R5,G0~G5,B0~B5,.
Remark
Note 1 Note 2 Note 2
3.1.3 Backlight driving conditions
Item
Symbol
Min.
Values Typ.
Max.
Unit
Remark
Voltage for LED Backlight Current for LED Backlight LED life time
VL IL --
--20000
19.2 40 --
-- V -- mA -- Hr
Note 1 Note 2
Note 1: The LED Supply Voltage is defined by the number of LED at Ta=25℃ and IL =40mA. Note 2: The “LED life time” is defined as the module brightness decrease to 50% original brightness at
Ta=25℃ and IL =40mA.
AZ DISPLAYS
6
ATM0500D14-T(AZ DISPLAYS)TFT MODULE V1.0
3.2TimingCharacteristics 3.2.1Data Input Format
AZ DISPLAYS
7
ATM0500D14-T(AZ DISPLAYS)TFT MODULE V1.0
3.2.2 AC Electrical Characteristics
AZ DISPLAYS
8
ATM0500D14-T(AZ DISPLAYS)TFT MODULE V1.0
AZ DISPLAYS
9
ATM0500D14-T(AZ DISPLAYS)TFT MODULE V1.0
4.0 OPTICAL SPECIFICATIONS
Item
Viewing Angle
(CR≥10)
Response Time Contrast Ratio
Color Chromaticity
Luminance Luminance Uniformity
Symbol
θL θR θT θB TON + TOFF CR WX
WY
Condition Φ=180o(9 O'CLOCK)
Φ=0o(3 O'CLOCK) Φ=90o(12 O'CLOCK) Φ=270o(6 O'CLOCK)
Normal Θ=Φ=0o
Values
Min. 40 40 20 40 -400 0.280
Typ. 50 50 30 50 32 800 0.320
Max. ----42 --
0.360
0.300 0.340 0.380
L
240 --
--
YU -- 85 --
Unit
degree
msec ----
cd/m2 %
Remark Note 1
Note 3 Note 4 Note 2 Note 5 Note 6 Note 6 Note 7
Test Conditions:
1. IL=40mA (Backlight current), the ambient temperature is 25℃. 2. The test systems refer to Note 2.
Note 1: Definition of viewing angle range
AZ DISPLAYS
Figure 4.1 Definition of viewing angle.
10
ATM0500D14-T(AZ DISPLAYS)TFT MODULE V1.0
Note 2: Definition o.