| No. | Part # | Manufacturer | Description | Datasheet |
|---|---|---|---|---|
|
|
|
NXP |
Signal Souces Switch |
|
|
|
|
NXP |
2 x 7 W stereo Bridge Tied Load BTL audio amplifier s s s s s s s s s Few external components Fixed gain Standby and mute mode No on/off switching plops Low standby current High supply voltage ripple rejection Outputs short-circuit protected to ground, supply and across the load Thermally protected Pr |
|
|
|
|
NXP |
CONTROL CIRCUIT FOR SMPS Be sure to visit ChipDocs site for more information http://www.chipdocs.com Be sure to visit ChipDocs site for more information http://www.chipdocs.com |
|
|
|
|
NXP |
Multiple voltage regulator s Three enable pin controlled standby regulators: x REG1: 5 V / 600 mA controlled by the EN1 input x REG2: 3.3 V / 200 mA controlled by the EN2/3 input x REG3: 1.9 V / 150 mA controlled by the EN2/3 input s Four mode pin controlled switched regulator |
|
|
|
|
NXP |
Gating / Frequency Divider |
|
|
|
|
NXP |
26 W BTL and 2 x 13 W SE power amplifiers • Requires very few external components • High output power • Low output offset voltage (BTL channel) • Fixed gain • Diagnostic facility (distortion, short-circuit and temperature detection) • Good ripple rejection • Mode select switch (operating, mu |
|
|
|
|
NXP |
Universal HiFi audio processor for TV • Multi-source selector switches six AF inputs (three stereo sources or six mono sources) • Each of the input signals can be switched to each of the outputs (crossbar switch) • Outputs for loudspeaker channel, headphone channel and peri-TV connector |
|
|
|
|
NXP |
Triple video output amplifier • Typical bandwidth of 5.5 MHz for an output signal of 60 V (p-p) • High slew rate of 900 V/µs • No external components required • Very simple application • Single supply voltage of 200 V • Internal reference voltage of 2.5 V • Fixed gain of 50 • Bla |
|
|
|
|
NXP |
4 x 40 W BTL quad car radio power amplifier • Requires very few external components • High output power • Low output offset voltage • Fixed gain • Diagnostic facility (distortion, short-circuit and temperature pre-warning) • Good ripple rejection • Mode select switch (operating, mute and stand |
|
|
|
|
NXP |
2 to 6 W audio power amplifier are: • single in-line (SIL) construction for easy mounting • separated preamplifier and power amplifier • high output power • thermal protection • high input impedance • low current drain • limited noise behaviour at radio frequencies QUICK REFERENCE |
|
|
|
|
NXP |
2 x 8 W stereo BTL audio amplifier • DC volume control • Few external components • Mute mode • Thermal protection • Short-circuit proof • No switch-on and switch-off clicks • Good overall stability • Low power consumption • Low HF radiation • ESD protected on all pins. QUICK REFERENCE |
|
|
|
|
NXP |
BTSC-stereo/SAP/DBX decoder and DBX expander • DBX decoder, MPX decoder and SAP decoder on chip • Extensive switching possibilities for the AF outputs and the extra headphone output • Stereo and SAP signal available simultaneously • Reliable stereo/SAP identification by means of the noise detec |
|
|
|
|
NXP |
30 Msps analog-to-digital interface for CCD cameras • Clamp and Track/Hold (CTH) circuit with adjustable bandwidth, Programmable Gain Amplifier (PGA), 12-bit Analog-to-Digital Converter (ADC) and reference regulator • Fully programmable via a 3-wire serial interface • Sampling frequency up to 30 MHz • |
|
|
|
|
NXP |
DVB-T channel receiver • 2 and 8 kbytes Coded Orthogonal Frequency Division Multiplexer (COFDM) demodulator (fully DVB-T compliant: ETSI 300-744) • All modes supported, including hierarchical modes • Fully automatic transmission parameters detection (including Fast Fourier |
|
|
|
|
NXP |
Class AB stereo headphone driver and benefits Wide temperature range No switch ON/OFF clicks Excellent power supply ripple rejection Low power consumption Short-circuit resistant High performance High signal-to-noise ratio High slew rate Low distortion Large outp |
|
|
|
|
NXP |
12-bit high-speed Analog-to-Digital Converter ADC • 12-bit resolution • Sampling rate up to 55 MHz • −3 dB bandwidth of 190 MHz • 5 V power supplies • Binary or twos-complement CMOS outputs • In-range CMOS-compatible output • TLL-CMOS compatible static digital inputs • 3 to 5 V CMOS-compatible digit |
|
|
|
|
NXP |
10-bit high-speed low-power ADC with internal reference regulator • 10-bit resolution (binary or gray code) • Sampling rate up to 40 MHz (/4 version) Sampling rate up to 80 MHz (/8 version) • DC sampling allowed • One clock cycle conversion only • High signal-to-noise ratio over a large analog input frequency range |
|
|
|
|
NXP |
Triple 10-bit video Digital-to-Analog Converter DAC • 10-bit resolution • Sampling rate up to: – 50 MHz for normal mode; RL = 37.5 Ω – 35 MHz for LOW power mode; RL = 150 Ω • Internal current reference • Current reference selector for: – normal mode, RL = 37.5 Ω (typ.) – low-power mode, RL = 150 Ω (ty |
|
|
|
|
NXP |
Spatial/ stereo and pseudo-stereo sound circuit • Three switched functions: – spatial (widened stereo image) – stereo – pseudo-stereo (artificial stereo from a mono source) • Offset compensated operational amplifiers to reduce switch noise • LED driver outputs to facilitate indication of selected |
|
|
|
|
NXP Semiconductors |
2 X 210 W class-D power amplifier low quiescent current consumption. The TDA8954 is supplied with two diagnostic pins for monitoring the status of Thermal Fold Back (TFB), Over Current Protection (OCP) and other protection circuits. 2. Features High output power in typical applica |
|