PCA9557

PCA9550 : The PCA9550 LED blinker blinks LEDs in I2C-bus and SMBus applications where it is necessary to limit bus traffic or free up the I2C master's (MCU, MPU, DSP, chip set, etc.) timer. The uniqueness of this device is the internal oscillator with two programmable blink rates. To blink LEDs using normal I/O expanders like the PCF8574 or PCA9554, the bus master must send repeated commands to turn the LED on and off. This greatly increases the amount of traffic on the I2C-bus and uses up one of the master's timers. The PCA9550 LED blinker instead requires only the initial set-up command to program BLINK RATE 1 and BLINK RATE 2 (i.e., the frequency and duty cycle). From then on, only one command from t.

PCA9551 : The PCA9551 LED blinker blinks LEDs in I2C-bus and SMBus applications where it is necessary to limit bus traffic or free up the I2C-bus master's (MCU, MPU, DSP, chip set, etc.) timer. The uniqueness of this device is the internal oscillator with two programmable blink rates. To blink LEDs using normal I/O expanders like the PCF8574 or PCA9554, the bus master must send repeated commands to turn the LED on and off. This greatly increases the amount of traffic on the I2C-bus and uses up one of the master's timers. The PCA9551 LED blinker instead requires only the initial set-up command to program BLINK RATE 1 and BLINK RATE 2 (i.e., the frequency and duty cycle) for each individual output. From t.

PCA9552 : The PCA9552 LED blinker blinks LEDs in I2C-bus and SMBus applications where it is necessary to limit bus traffic or free up the I2C-bus controller's (MCU, MPU, DSP, chip set, etc.) timer. The uniqueness of this device is the internal oscillator with two programmable blink rates. To blink LEDs using normal I/O expanders like the PCF8574 or PCA9554, the bus controller must send repeated commands to turn the LED on and off. This greatly increases the amount of traffic on the I2C-bus and uses up one of the controller's timers. The PCA9552 LED blinker instead requires only the initial setup command to program BLINK RATE 1 and BLINK RATE 2 (that is, the frequency and duty cycle) for each individua.

PCA9553 : PIN NUMBER 1 2 3 4 5 6 7 8 SYMBOL LED0 LED1 LED2 VSS LED3 SCL SDA VDD FUNCTION LED driver 0 LED driver 1 LED driver 2 Supply ground LED driver 3 Serial clock line Serial data line Supply voltage • Packages offered: SO8, TSSOP8 (MSOP8) DESCRIPTION The PCA9553 LED Blinker blinks LEDs in I2C and SMBus applications where it is necessary to limit bus traffic or free up the I2C Master’s (MCU, MPU, DSP, chipset, etc.) timer. The uniqueness of this device is the internal oscillator with two programmable blink rates. To blink LEDs using normal I/O Expanders like the PCF8574 ORDERING INFORMATION PACKAGES 8-Pin Plastic SO 8-Pin Plastic SO 8-Pin Plastic TSSOP (MSOP) 8-Pin Plastic TSSOP (MSOP) TEMPERAT.

PCA9554 : This 8-bit I/O expander for the two-line bidirectional bus (I2C) is designed for 2.3-V to 5.5-V VCC operation. It provides general-purpose remote I/O expansion for most microcontroller families via the I2C interface [serial clock (SCL), serial data (SDA)]. The PCA9554 consists of one 8-bit Configuration (input or output selection), Input, Output, and Polarity Inversion (active high or active low) registers. At power on, the I/Os are configured as inputs with a weak pullup to VCC. However, the system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or output is kept in the corresponding Input or Output register. The polar.

PCA9554 : The PCA9554 and PCA9554A are 16-pin CMOS devices that provide 8 bits of General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and were developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a simple solution when additional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, and so on. The PCA9554/PCA9554A consist of an 8-bit Configuration register (Input or Output selection); 8-bit Input Port register, 8-bit Output Port register.

PCA9554 : The PCA9554 is a CMOS device that provides 8−bit parallel input/output port expansion for I2C and SMBus compatible applications. This I/O expander provides a simple solution in applications where additional I/Os are needed: sensors, power switches, LEDs, pushbuttons, and fans. The PCA9554 consist of an input port register, an output port register, a configuration register, a polarity inversion register and an I2C/SMBus−compatible serial interface. Any of the eight I/Os can be configured as an input or output by writing to the configuration register. The system master can invert the PCA9554 input data by writing to the active−high polarity inversion register. The PCA9554 features an active lo.

PCA9554A : The PCA9554 and PCA9554A are 16-pin CMOS devices that provide 8 bits of General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and were developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, 400 kHz clock frequency, and smaller packaging. I/O expanders provide a simple solution when additional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, and so on. The PCA9554/PCA9554A consist of an 8-bit Configuration register (Input or Output selection); 8-bit Input Port register, 8-bit Output Port register.

PCA9554A : This 8-bit I/O expander for the two-line bidirectional bus (I2C) is designed for 2.3-V to 5.5-V VCC operation. It provides general-purpose remote I/O expansion for most microcontroller families via the I2C interface [serial clock (SCL), serial data (SDA)]. The PCA9554A consists of one 8-bit Configuration (input or output selection), Input, Output, and Polarity Inversion (active high or active low) registers. At power on, the I/Os are configured as inputs with a weak pullup to VCC. However, the system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or output is kept in the corresponding Input or Output register. The pola.

PCA9555 : The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallel Input/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed to enhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvements include higher drive capability, 5 V I/O tolerance, lower supply current, individual I/O configuration, and smaller packaging. I/O expanders provide a simple solution when additional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc. The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Output and Polarity Inversion (active HIGH or active LOW operation) registers. The system master can enab.

PCA9555 : This 16-bit I/O expander for the two-line bidirectional bus (I2C) is designed for 2.3-V to 5.5-V VCC operation. It provides general-purpose remote I/O expansion for most microcontroller families via the I2C interface [serial clock (SCL), serial data (SDA)]. The PCA9555 consists of two 8-bit Configuration (input or output selection), Input Port, Output Port, and Polarity Inversion (active high or active low operation) registers. At power on, the I/Os are configured as inputs. The system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or output is kept in the corresponding Input or Output register. The polarity of the Inp.

PCA9555A : The PCA9555A is a low-voltage 16-bit General Purpose Input/Output (GPIO) expander with interrupt and weak pull-up resistors for I2C-bus/SMBus applications. NXP I/O expanders provide a simple solution when additional I/Os are needed while keeping interconnections to a minimum, for example, in ACPI power switches, sensors, push buttons, LEDs, fan control, etc. In addition to providing a flexible set of GPIOs, the wide VDD range of 1.65 V to 5.5 V allows the PCA9555A to interface with next-generation microprocessors and microcontrollers where supply levels are dropping down to conserve power. The PCA9555A contains the PCA9555 register set of four pairs of 8-bit Configuration, Input, Output, and.

PCA9556 : The PCA9556 is a silicon CMOS circuit which provides parallel input/output expansion for SMBus applications. The PCA9556 consists of an 8-bit input port register, 8-bit output port register, and an SMBus interface. It has low current consumption and a high impedance open drain output pin, I/O0. The SMBus system master can reset the PCA9556 in the event of a timeout by asserting a LOW on the reset input. The SMBus system master can also invert the PCA9556 inputs by writing to their active HIGH polarity inversion bits. Finally, the SMBus system master can enable the PCA9556’s I/Os as either inputs or outputs by writing to their I/O configuration bits. The power-on reset sets the registers to t.

PCA9557 : The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion for SMBus and I2C applications. The PCA9557 consists of an 8-bit input port register, 8-bit output port register, and an I2C/SMBus interface. It has low current consumption and a high impedance open drain output pin, I/O0. The system master can enable the PCA9557’s I/O as either input or output by writing to the configuration register. exceeds 100 mA 200 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101 A0 3 A1 4 A2 5 I/O0 6 I/O1 7 VSS 8 su01045 Figure 1. Pin configuration PIN DESCRIPTION PIN NUMBER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SYMBOL SCL SDA A0 A1 A2 I/O0 I/O1 VSS I/O2 I/O3 I/O4 I/O5 I/O6 I/.

PCA9559 : The primary function of the 5-bit multiplexer, 1-bit latch is to enable system configuration. PIN CONFIGURATION 2 I C SCL SDA A1 A0 1 2 3 4 5 6 7 8 9 20 VCC 19 WP 18 OVERRIDE # 17 NON_MUXED_OUT 16 MUX_OUT A 15 MUX_OUT B 14 MUX_OUT C 13 MUX_OUT D 12 MUX_OUT E 11 MUX_SELECT I2C MUX_IN A MUX_IN B MUX_IN C MUX_IN D MUX_IN E GND 10 SW00216 ORDERING INFORMATION PACKAGES 20-Pin Plastic TSSOP TEMPERATURE RANGE 0°C to +70°C ORDER CODE PCA9559 PW DH DRAWING NUMBER SOT360-1 FUNCTIONAL DESCRIPTION When the MUX_SELECT signal is logic 0, the multiplexer will select the data from the non-volatile register to drive on the MUX_OUT pins. When the MUX_SELECT signal is logic 1, the multiplexer will se.