SI9112

SI9110 : The Si9110/9111 are BiC/DMOS integrated circuits designed for use as high-performance switchmode controllers. A high-voltage DMOS input allows the controller to work over a wide range of input voltages (10- to 120-VDC). Current-mode PWM control circuitry is implemented in CMOS to reduce internal power consumption to less than 10 mW. A push-pull output driver provides high-speed switching for MOSPOWER devices large enough to supply 50 W of output power. When combined with an output MOSFET and transformer, the Si9110/9111 can be used to implement single-ended power converter topologies (i.e., flyback, forward, and cuk). The Si9110/9111 are available in a standard 14-pin plastic DIP and standar.

Si9111 : The Si9110/9111 are BiC/DMOS integrated circuits designed for use as high-performance switchmode controllers. A high-voltage DMOS input allows the controller to work over a wide range of input voltages (10- to 120-VDC). Current-mode PWM control circuitry is implemented in CMOS to reduce internal power consumption to less than 10 mW. A push-pull output driver provides high-speed switching for MOSPOWER devices large enough to supply 50 W of output power. When combined with an output MOSFET and transformer, the Si9110/9111 can be used to implement single-ended power converter topologies (i.e., flyback, forward, and cuk). The Si9110/9111 are available in a standard 14-pin plastic DIP and standar.

SI9113DB : As discussed in application note, AN728, the Si9113 power supply controller is an ideal choice for ISDN terminal equipment, where high efficiency at a low power level is one of most important criteria. Therefore, Vishay Siliconix has developed versions of a dual output flyback application demonstration boards, the Si9113D1 and the Si9113D2, which use different regulation schemes. These readily available demo boards are configured to deliver approximately 800 mW at 3.3-V, and40-V. These outputs and can be easily modified for other output voltages at approximately same power level. The flyback converters are designed to operate from a wide input voltage range of 28 V to 99 V and are polarity p.

Si9114 : The Si9114 is a BiC/DMOS current-mode pulse width modulation (PWM) controller IC for high-frequency dc/dc converters. Single-ended topologies (forward and flyback) can be implemented at frequencies up to 1 MHz. The oscillator has an internal divide-by-two that limits the duty ratio to 50%. An oscillator sync output allows converters to be synchronized in phase as well as in frequency, in a master/slave configuration. The output inverter can typicallysource 500rnA and sink 700 rnA. Shoot-through current is all but eliminated to Functional Block Diagram • Latched SHUIDOWN • Soft-Start • 1.5-MHz Error Amp minimize supply current requirements. The high-voltage DMOS transistor allows the IC to i.

SI9114A : The Si9114A is a BiC/DMOS current-mode pulse width modulation (PWM) controller IC for high-frequency dc/dc converters. Single-ended topologies (forward and flyback) can be implemented at frequencies up to 1 MHz. The oscillator has an internal divide-by-two that limits the duty ratio to 50%. An oscillator sync output allows converters to be synchronized in phase as well as in frequency, in a master/slave configuration. The output inverter can typically source 500 mA and sink 700 mA. Shoot-through current is all but eliminated to minimize supply current requirements. The high-voltage DMOS transistor allows the IC to interface directly to bus voltages up to 200 V. Other features include a 1.5% .

SI9117 : The Si9117 high-efficiency converter for telecom systems running off 48 V is ideal for emerging applications such as interactive video (IV) set-top boxes and microcell base stations, such as those used for Personal Communications Systems (PCS). IV set-top boxes and microcell base stations typically require less than 15 W of power and have access to the analog telephone line power. Both IV set-top boxes and microcell base stations process extremely low-level, modulated analog signals (on the order of mVs), making the frequency and energy content of radiated and conducted noise a major issue. These application circuits are also constrained in terms of available board space and place a premium .