MC33197

MC33192 : The MC33192 is a serial stepper motor controller for use in harsh automotive applications using multiplex wiring. The MC33192 provides all the necessary four phase drive signals to control two phase bipolar stepper motors operated in either half or full step modes. Multiple stepper motor controllers can be operated on a real time basis at step frequencies up to 200 Hz using a single microcontroller (MCU). A primary attribute of operation is the utilization of the MI–Bus message media to provide high noise immunity communication ensuring very high operating reliability of motor stepping. The MC33192 is designed to drive bipolar stepper motors having a winding resistance of 80 Ω at 20°C with a.

MC33193 : Order this document by MC33193/D MC33193 Advance Information Automotive Direction Indicator The MC33193 is a new generation industry standard UAA1041 “Flasher”. It has been developed for enhanced EMI sensitivity, system reliability, and improved wiring simplification. The MC33193 is pin compatible with the UAA1041 and UAA1041B in the standard application configuration as shown in Figure 9, without lamp short circuit detection and using a 20 mΩ shunt resistor. The MC33193 has a standby mode of operation requiring very low standby supply current and can be directly connected to the vehicle’s battery. It includes an RF filter on the Fault detection pin (Pin 7) for EMI purposes. Fault detectio.

MC33195 : .

MC33197A : Order this document by MC33197A/D MC33197A Advance Information Automotive Wash Wiper Timer The MC33197A is a standard wiper timer control device designed for harsh automotive applications. The device can perform the intermittent, after wash, and continuous wiper timer functions. It is designed to directly drive a wiper motor relay. The MC33197A requires very few external components for full system implementation. The intermittent control pin can be switched to ground or Vbat to meet a large variety of possible applications. The intermittent timing can be fixed or adjustable via an external resistor. The MC33197A is built using bipolar technology and parametrically specified over the automo.

MC33198 : Introduction The MC33198D is a high side TMOS driver, dedicated for automotive applications. It is used in conjunction with an external power MOSFET for high side drive applications. The device can drive and protect a large variety of MOSFET. The device has CMOS compatible input control, charge pump to drive the MOSFET gate, fault detection circuitry based on programmable Vds monitoring to detect shorted load. It also includes a programmable timer function to eliminate undesired switch off due to in rush currents and a status pin which reports the output status in both on and off MOSFET state. The device uses few external components and offers an economical solution to large current high sid.

MC33198 : Freescale Semiconductor Technical Data Automotive High-Side TMOS Driver Document Number: MC33198 Rev. 2.0, 11/2006 33198 The MC33198 is a high-side TMOS driver, dedicated to automotive applications. It is used in conjunction with an external power MOSFET for high-side drive applications. The device can drive and protect a HIGH-SIDE TMOS DRIVER large variety of MOSFETs. The device has a CMOS compatible input control, charge pump to drive the MOSFET gate, and fault detection circuitry based on programmable VDS monitoring to detect shorted loads. It also includes a programmable timer function to eliminate undesired switch off due to in rush currents, and a status pin which reports the .

MC33199 : Order this document by MC33199/D Automotive ISO 9141 Serial Link Driver The MC33199D is a serial interface circuit used in diagnostic applications. It is the interface between the microcontroller and the special K and L Lines of the ISO diagnostic port. The MC33199D has been designed to meet the “Diagnosis System ISO 9141” specification. The device has a bi–directional bus K Line driver, fully protected against short circuits and over temperature. It also includes the L Line receiver, used during the wake up sequence in the ISO transmission. The MC33199 has a unique feature which allows transmission baud rate up to 200 k baud. MC33199 ISO 9141 SERIAL LINK DRIVER SEMICONDUCTOR TECHNICAL DA.