| Part Number | X9119 |
| Manufacturer | Renesas |
| Title | Digitally Potentiometer |
| Description | DATASHEET X9119 1024 Tap, Low Power, 2-Wire Interface, Digitally Controlled (XDCP™) Potentiometer FN8162 Rev 5.00 July 5, 2016 The X9119 integr... |
| Features |
• 1024 resistor taps – 10-bit resolution • 2-Wire serial interface for write, read, and transfer operations of the potentiometer • Wiper resistance, 40Ω typical at VCC = 5V • Four nonvolatile data registers • Nonvolatile storage of multiple wiper positions • Power-on recall, loads saved wiper positi... |
| File Size | 765.29KB |
| Datasheet |
|
X9118 : DATASHEET X9118 Dual Supply/Low Power/1024-Tap/2-Wire Bus Single Digitally-Controlled (XDCP™) Potentiometer FN8161 Rev 5.00 April 9, 2014 The X9118 is a single digitally controlled potentiometer (XDCP) on a monolithic CMOS integrated circuit. The digital controlled potentiometer is implemented using 1023 resistive elements in a series array. Between each element are tap points connected to the wiper terminal through switches. The position of the wiper on the array is controlled by the user through the 2-wire bus interface. The potentiometer has associated with it a volatile Wiper Counter Register (WCR) and a four non-volatile Data Registers that can be directly written to and read by the .
X9116 : DATASHEET X9116 Low Noise, Low Power, Low Cost Digitally Controlled Potentiometer (XDCP™) FN8160 Rev 3.00 February 3, 2011 The Intersil X9116 is a digitally controlled nonvolatile potentiometer designed to be used in trimmer applications. The pot consists of 15 equal resistor segments that connect to the wiper pin through programmable CMOS switches. The tap position is programmed through a 3-wire up/down serial port. The last position of the wiper is stored in a nonvolatile memory location which is recalled at the time of power up of the device. The wiper moves through sequential tap positions with inputs on the serial port. A falling edge on INC (bar) causes the tap position to increment.
X9116 : APPLICATION NOTE A V A I L A B L E AN99 • AN115 • AN120 • AN124 • AN133 • AN134 Low Noise, Low Power, Low Cost X9116 Digitally Controlled Potentiometer (XDCP™) FEATURES • • • • • • • • Solid-state nonvolatile 16 wiper taps 3-wire up/down serial interface VCC = 2.7V and 5V Active current 50µA max. Standby current 1µA max. RTOTAL = 10KΩ Packages: MSOP-8, SOIC DESCRIPTION The Xicor X9116 is a digitally controlled nonvolatile potentiometer designed to be used in trimmer applications. The pot consists of 15 equal resistor segments that connect to the wiper pin through programmable CMOS switches. The tap position is programmed through a 3-wire up/down serial port. The last position of the wi.
X9111 : DATASHEET X9111 Single Supply/Low Power/1024-Tap/SPI Bus/Single Digitally-Controlled (XDCP™) Potentiometer FN8159 Rev 5.00 October 13, 2016 The X9111 integrates a single, digitally controlled potentiometer (XDCP) on a monolithic CMOS integrated circuit. The digital controlled potentiometer is implemented using 1023 resistive elements in a series array. Between each element are tap points connected to the wiper terminal through switches. The position of the wiper on the array is controlled by the user through the SPI bus interface. The potentiometer has associated with it a volatile Wiper Counter Register (WCR) and four nonvolatile Data Registers that can be directly written to and read by.