TLV1704 Datasheet PDF

TLV1012 : ORDERING INFORMATION The TLV1012 is an audio amplifier series for small-form-factor electret microphones. This two-wire amplifier is designed to replace JFET amplifiers currently in use. The TLV1012 is ideally suited for applications that require high signal integrity in the presence of ambient or RF noise, such as in cellular communications. The TLV1012 audio amplifier is specified for operation over a 2.2-V to 5-V supply voltage range with a fixed gain of 15.6 dB. The device offers excellent THD, gain accuracy, and temperature stability compared to JFET microphones. The TLV1012 enables a two-pin electret microphone solution, which provides direct pin-to-pin compatibility with the existing .

TLV1018 : ORDERING INFORMATION The TLV1018 is an audio amplifier for small-form-factor electret microphones and is designed to replace the currently implemented JFET preamplifiers. The TLV1018 is ideal for extended battery-life applications, such as a Bluetooth™ communication link. The addition of a third pin to an electret microphone that incorporates a TLV1018 allows for a dramatic reduction in supply current compared to a JFET-equipped electret microphone. Microphone supply current is reduced to 70 µA, assuring longer battery life. The TLV1018 is specified for supply voltages from 1.7 V to 5 V and has fixed voltage gains of 15 dB and 25 dB. It offers low output impedance over the voice bandwidth, e.

TLV1117 : The TLV1117 is a positive low-dropout voltage regulator designed to provide up to 800 mA of output current. The device is available in 1.5-V, 1.8-V, 2.5V, 3.3-V, 5-V, and adjustable-output voltage options. All internal circuitry is designed to operate down to 1-V input-to-output differential. Dropout voltage is specified at a maximum of 1.3 V at 800 mA, decreasing at lower load currents. Package Information PART NUMBER PACKAGE(1) BODY SIZE (NOM) DCY (SOT-223, 4) 6.50 mm × 3.50 mm DRJ (WSON, 8) 4.00 mm × 4.00 mm TLV1117 KVU (TO-252, 3) 6.60 mm × 6.10 mm KCS (TO-220, 3) 10.16 mm × 8.70 mm KCT (TO-220, 3) 10.16 mm × 8.59 mm KTT (DDPAK/ TO-263, 3) 10.18 mm × 8.41 mm (1) For all avai.

TLV1117LV : The TLV1117LV low-dropout (LDO) linear regulator is a low input voltage version of the popular TLV1117 voltage regulator. The TLV1117LV is an extremely low-power device that consumes 500 times lower quiescent current than traditional 1117 voltage regulators, making the device designed for applications that mandate very low standby current. The TLV1117LV LDO is also stable with 0 mA of load current; there is no minimum load requirement, making the device a good choice for applications where the regulator must power very small loads during standby in addition to large currents on the order of 1 A during normal operation. The TLV1117LV offers excellent line and load transient performance, res.

TLV1171 : The TLV1171 low-dropout (LDO) linear regulator is a low input voltage version of the popular 1117 voltage regulator. The TLV1171 is an extremely low-power device that consumes 500x lower quiescent current than the traditional 1117 voltage regulator, making the TLV1171 suitable for applications that mandate very low standby current. The TLV1171 LDO is also stable with 0 mA of load current; there is no minimum load requirement, making the device an ideal choice for applications where the regulator is required to power very small loads during standby in addition to large currents on the order of 1 A during normal operation. The TLV1171 offers excellent line and load transient performance, resul.

TLV1391 : ordering informaton The TLV1391 is a differential comparator built using a Texas Instruments low-voltage, high-speed bipolar process. These devices have been developed specifically for low-voltage, single-supply applications. Their enhanced performance makes them excellent replacements for the LM393 in the improved 3-V and 5-V system designs. The TLV1391, with its typical supply current of only 80 µA, is ideal for low-power systems. Response time also has been improved to 0.7 µs. ORDERING INFORMATION TA PACKAGE† ORDERABLE PART NUMBER TOP-SIDE MARKING‡ −0°C to 70°C SOT-23-5 (DBV) Reel of 3000 Reel of 250 TLV1391CDBVR TLV1391CDBVT Y3D_ −40°C to 85°C SOT-23-5 (DBV) Reel of 3000 Reel.

TLV1504 : .

TLV1508 : .

TLV1543 : The TLV1543C, TLV1543I, and TLV1543M are CMOS 10-bit, switched-capacitor, successiveapproximation, analog-to-digital converters. These devices have three inputs and a 3-state output [chip select (CS), input-output clock (I/O CLOCK), address input (ADDRESS), and data output (DATA OUT)] that provide a direct 4-wire interface to the serial port of a host processor. The devices allow high-speed data transfers from the host. DB, DW, FK, J, OR N PACKAGE (TOP VIEW) A0 1 A1 2 A2 3 A3 4 A4 5 A5 6 A6 7 A7 8 A8 9 GND 10 20 VCC 19 EOC 18 I/O CLOCK 17 ADDRESS 16 DATA OUT 15 CS 14 REF + 13 REF − 12 A10 11 A9 FN PACKAGE (TOP VIEW) A2 A1 A0 VCC EOC A3 3 2 1 20 19 4 18 I/O CLOCK A4 5 17 ADDRESS .

TLV1543C : The TLV1543C, TLV1543I, and TLV1543M are CMOS 10-bit, switched-capacitor, successiveapproximation, analog-to-digital converters. These devices have three inputs and a 3-state output [chip select (CS), input-output clock (I/O CLOCK), address input (ADDRESS), and data output (DATA OUT)] that provide a direct 4-wire interface to the serial port of a host processor. The devices allow high-speed data transfers from the host. DB, DW, FK, J, OR N PACKAGE (TOP VIEW) A0 1 A1 2 A2 3 A3 4 A4 5 A5 6 A6 7 A7 8 A8 9 GND 10 20 VCC 19 EOC 18 I/O CLOCK 17 ADDRESS 16 DATA OUT 15 CS 14 REF + 13 REF − 12 A10 11 A9 FN PACKAGE (TOP VIEW) A2 A1 A0 VCC EOC A3 3 2 1 20 19 4 18 I/O CLOCK A4 5 17 ADDRESS .

TLV1543I : The TLV1543C, TLV1543I, and TLV1543M are CMOS 10-bit, switched-capacitor, successiveapproximation, analog-to-digital converters. These devices have three inputs and a 3-state output [chip select (CS), input-output clock (I/O CLOCK), address input (ADDRESS), and data output (DATA OUT)] that provide a direct 4-wire interface to the serial port of a host processor. The devices allow high-speed data transfers from the host. DB, DW, FK, J, OR N PACKAGE (TOP VIEW) A0 1 A1 2 A2 3 A3 4 A4 5 A5 6 A6 7 A7 8 A8 9 GND 10 20 VCC 19 EOC 18 I/O CLOCK 17 ADDRESS 16 DATA OUT 15 CS 14 REF + 13 REF − 12 A10 11 A9 FN PACKAGE (TOP VIEW) A2 A1 A0 VCC EOC A3 3 2 1 20 19 4 18 I/O CLOCK A4 5 17 ADDRESS .

TLV1543M : The TLV1543C, TLV1543I, and TLV1543M are CMOS 10-bit, switched-capacitor, successiveapproximation, analog-to-digital converters. These devices have three inputs and a 3-state output [chip select (CS), input-output clock (I/O CLOCK), address input (ADDRESS), and data output (DATA OUT)] that provide a direct 4-wire interface to the serial port of a host processor. The devices allow high-speed data transfers from the host. DB, DW, FK, J, OR N PACKAGE (TOP VIEW) A0 1 A1 2 A2 3 A3 4 A4 5 A5 6 A6 7 A7 8 A8 9 GND 10 20 VCC 19 EOC 18 I/O CLOCK 17 ADDRESS 16 DATA OUT 15 CS 14 REF + 13 REF − 12 A10 11 A9 FN PACKAGE (TOP VIEW) A2 A1 A0 VCC EOC A3 3 2 1 20 19 4 18 I/O CLOCK A4 5 17 ADDRESS .

TLV1544 : The TLV1544 and TLV1548 are CMOS 10-bit switched-capacitor successive-approximation (SAR) analog-to-digital (A/D) converters. Each device has a chip select (CS), input-output clock (I/O CLK), data input (DATA IN) and serial data output (DATA OUT) that provide a direct 4-wire synchronous serial peripheral interface (SPI™, QSPI™) port of a host microprocessor. When interfacing with a TMS320 DSP, an additional frame sync signal (FS) indicates the start of a serial data frame. The devices allow high-speed data transfers from the host. The INV CLK input provides further timing flexibility for the serial interface. DATA OUT DATA IN I/O CLK EOC VCC A0 A1 A2 A0 A1 A2 A3 A4 A5 A6 A7 CSTART GND D OR.

TLV1544C : The TLV1544 and TLV1548 are CMOS 10-bit switched-capacitor successive-approximation (SAR) analog-to-digital (A/D) converters. Each device has a chip select (CS), input-output clock (I/O CLK), data input (DATA IN) and serial data output (DATA OUT) that provide a direct 4-wire synchronous serial peripheral interface (SPI™, QSPI™) port of a host microprocessor. When interfacing with a TMS320 DSP, an additional frame sync signal (FS) indicates the start of a serial data frame. The devices allow high-speed data transfers from the host. The INV CLK input provides further timing flexibility for the serial interface. DATA OUT DATA IN I/O CLK EOC VCC A0 A1 A2 A0 A1 A2 A3 A4 A5 A6 A7 CSTART GND D OR.

TLV1544I : The TLV1544 and TLV1548 are CMOS 10-bit switched-capacitor successive-approximation (SAR) analog-to-digital (A/D) converters. Each device has a chip select (CS), input-output clock (I/O CLK), data input (DATA IN) and serial data output (DATA OUT) that provide a direct 4-wire synchronous serial peripheral interface (SPI™, QSPI™) port of a host microprocessor. When interfacing with a TMS320 DSP, an additional frame sync signal (FS) indicates the start of a serial data frame. The devices allow high-speed data transfers from the host. The INV CLK input provides further timing flexibility for the serial interface. DATA OUT DATA IN I/O CLK EOC VCC A0 A1 A2 A0 A1 A2 A3 A4 A5 A6 A7 CSTART GND D OR.

TLV1548 : The TLV1544 and TLV1548 are CMOS 10-bit switched-capacitor successive-approximation (SAR) analog-to-digital (A/D) converters. Each device has a chip select (CS), input-output clock (I/O CLK), data input (DATA IN) and serial data output (DATA OUT) that provide a direct 4-wire synchronous serial peripheral interface (SPI™, QSPI™) port of a host microprocessor. When interfacing with a TMS320 DSP, an additional frame sync signal (FS) indicates the start of a serial data frame. The devices allow high-speed data transfers from the host. The INV CLK input provides further timing flexibility for the serial interface. DATA OUT DATA IN I/O CLK EOC VCC A0 A1 A2 A0 A1 A2 A3 A4 A5 A6 A7 CSTART GND D OR.

TLV1548-EP : The TLV1548 is a CMOS 10-bit switched-capacitor successive-approximation (SAR) analog-to-digital (A/D) converter. The device has a chip select (CS), input-output clock (I/O CLK), data input (DATA IN) and serial data output (DATA OUT) that provides a direct 4-wire synchronous serial peripheral interface (SPI, QSPI) port of a host microprocessor. When interfacing with a TMS320 DSP, an additional frame sync signal (FS) indicates the start of a serial data frame. The device allows high-speed data transfers from the host. The INV CLK input provides further timing flexibility for the serial interface. In addition to a high-speed converter and versatile control capability, the device has an on-c.