Peripheral Controller. CY7C63801 Datasheet

CY7C63801 Controller. Datasheet pdf. Equivalent

CY7C63801 Datasheet
Recommendation CY7C63801 Datasheet
Part CY7C63801
Description Low-Speed USB Peripheral Controller
Feature CY7C63801; CY7C63310 CY7C638xx enCoRe™ II Low-Speed USB Peripheral Controller 1.0 Features • enCoReTM II USB—.
Manufacture Cypress Semiconductor
Datasheet
Download CY7C63801 Datasheet




Cypress Semiconductor CY7C63801
CY7C63310
CY7C638xx
enCoRe™ II
Low-Speed USB Peripheral Controller
1.0 Features
• enCoReTM II USB—“enhanced Component Reduction”
— Crystalless oscillator with support for an external clock.
The internal oscillator eliminates the need for an external
crystal or resonator
— Two internal 3.3V regulators and internal USB pull-up
resistor
www.DataSheet4U.com
— Configurable IO for real-world interface without external
components
• USB Specification Compliance
— Conforms to USB Specification, Version 2.0
— Conforms to USB HID Specification, Version 1.1
— Supports one Low-Speed USB device address
— Supports one control endpoint and two data endpoints
— Integrated USB transceiver with dedicated 3.3V
regulator for USB signalling and D- pull up.
• Enhanced 8-bit microcontroller
— Harvard architecture
— M8C CPU speed can be up to 24 MHz or sourced by an
external clock signal
• Internal memory
— Up to 256 bytes of RAM
— Up to eight Kbytes of Flash including EEROM emulation
• Interface can autoconfigure to operate as PS/2 or USB
— No external components for switching between PS/2 and
USB modes
— No GPIO pins needed to manage dual-mode capability
• Low power consumption
— Typically 10 mA at 6 MHz
— 10 µA sleep
• In-system re-programmability
— Allows easy firmware update
• General purpose I/O ports
— Up to 20 General Purpose I/O (GPIO) pins
— High current drive on GPIO pins. Configurable 8- or 50-
mA/pin current sink on designated pins
— Each GPIO port supports high-impedance inputs,
configurable pull up, open drain output, CMOS/TTL
inputs, and CMOS output
— Maskable interrupts on all I/O pins
• A dedicated 3.3V regulator for the USB PHY. Aids in
signalling and D-line pull-up
• 125 mA 3.3V voltage regulator can power external 3.3V
devices
• 3.3V I/O pins
— 4 I/O pins with 3.3V logic levels
— Each 3.3V pin supports high-impedance input, internal
pull up, open drain output or traditional CMOS output
• SPI serial communication
— Master or slave operation
— Configurable up to 4 Mbit/second transfers in the master
mode
— Supports half duplex single data line mode for optical
sensors
• 2-channel 8-bit or 1-channel 16-bit capture timer registers.
Capture timer registers store both rising and falling edge
times
— Two registers each for two input pins
— Separate registers for rising and falling edge capture
— Simplifies interface to RF inputs for wireless applications
• Internal low-power wake-up timer during suspend mode
— Periodic wake-up with no external components
• 12-bit Programmable Interval Timer with interrupts
• Advanced development tools based on Cypress
MicroSystems PSoC™ tools
• Watchdog timer (WDT)
• Low-voltage detection with user-configurable threshold
voltages
• Operating voltage from 4.0V to 5.5VDC
• Operating temperature from 0–70°C
• Available in 16/18-pin PDIP, 16/18/24-pin SOIC, 24-pin
QSOP and 32-lead QFN packages
• Industry standard programmer support
1.1 Applications
The CY7C63310/CY7C638xx is targeted for the following
applications:
• PC HID devices
— Mice (optomechanical, optical, trackball)
• Gaming
— Joysticks
— Game pad
• General-purpose
— Barcode scanners
— POS terminal
— Consumer electronics
— Toys
— Remote controls
— Security dongles
Cypress Semiconductor Corporation • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600
Document 38-08035 Rev. *I
Revised September 26, 2006
[+] Feedback



Cypress Semiconductor CY7C63801
CY7C63310
CY7C638xx
2.0 Introduction
Cypress has reinvented its leadership position in the low-
speed USB market with a new family of innovative microcon-
trollers. Introducing enCoRe II USB — “enhanced Component
Reduction.” Cypress has leveraged its design expertise in
USB solutions to advance its family of low-speed USB micro-
controllers, which enable peripheral developers to design new
products with a minimum number of components. The
enCoRe II USB technology builds on to the enCoRe family.
The enCoRe family has an integrated oscillator that eliminates
the external crystal or resonator, reducing overall cost. Also
integrated into this chip are other external components
commonly found in low-speed USB applications such as pull-
www.DataSheeut4pUr.ceosmistors, wake-up circuitry, and a 3.3V regulator. All of this
reduces the overall system cost.
The enCoRe II is an 8-bit Flash-programmable microcontroller
with integrated low-speed USB interface. The instruction set
has been optimized specifically for USB and PS/2 operations,
although the microcontrollers can be used for a variety of other
embedded applications.
The enCoRe II features up to 20 general-purpose I/O (GPIO)
pins to support USB, PS/2 and other applications. The I/O pins
are grouped into four ports (Port 0 to 3). The pins on Port 0 and
Port 1 may each be configured individually while the pins on
Ports 2 and 3 may only be configured as a group. Each GPIO
port supports high-impedance inputs, configurable pull up,
open drain output, CMOS/TTL inputs, and CMOS output with
up to five pins that support programmable drive strength of up
to 50 mA sink current. GPIO Port 1 features four pins that
interface at a voltage level of 3.3 volts. Additionally, each I/O
pin can be used to generate a GPIO interrupt to the microcon-
troller. Each GPIO port has its own GPIO interrupt vector; in
addition GPIO Port 0 has three dedicated pins that have
independent interrupt vectors (P0.2 - P0.4).
The enCoRe II features an internal oscillator. With the
presence of USB traffic, the internal oscillator can be set to
precisely tune to USB timing requirements (24 MHz ±1.5%).
Optionally, an external 12 MHz or 24 MHz clock can be used
to provide a higher precision reference for USB operation. The
clock generator provides the 12 MHz and 24 MHz clocks that
remain internal to the microcontroller. The enCoRe II also has
a 12-bit programmable interval timer and a 16-bit Free-
Running Timer with Capture Timer registers. In addition, the
enCoRe II includes a Watchdog timer and a vectored interrupt
controller
The enCoRe II has up to eight Kbytes of Flash for user’s code
and up to 256 bytes of RAM for stack space and user
variables.
The Power-on reset circuit detects logic when power is applied
to the device, resets the logic to a known state, and begins
executing instructions at Flash address 0x0000. When power
falls below a programmable trip voltage generates reset or
may be configured to generate interrupt. There is a Low-
voltage detect circuit that detects when VCC drops below a
programmable trip voltage. It may be configurable to generate
an LVD interrupt to inform the processor about the low-voltage
event. POR and LVD share the same interrupt. There is no
separate interrupt for each. The Watchdog timer can be used
to ensure the firmware never gets stalled in an infinite loop.
The microcontroller supports 22 maskable interrupts in the
vectored interrupt controller. Interrupt sources include a USB
bus reset, LVR/POR, a programmable interval timer, a
1.024-ms output from the Free Running Timer, three USB
endpoints, two capture timers, four GPIO Ports, three Port 0
pins, two SPI, a 16-bit free running timer wrap, an internal
sleep timer, and a bus active interrupt. The sleep timer causes
periodic interrupts when enabled. The USB endpoints interrupt
after a USB transaction complete is on the bus. The capture
timers interrupt whenever a new timer value is saved due to a
selected GPIO edge event. A total of seven GPIO interrupts
support both TTL or CMOS thresholds. For additional flexi-
bility, on the edge sensitive GPIO pins, the interrupt polarity is
programmable to be either rising or falling.
The free-running 16-bit timer provides two interrupt sources:
the 1.024 ms outputs and the free running counter wrap
interrupt. The programmable interval timer can provide up to
1 µsec resolution and provides an interrupt everytime it
expires. These timers can be used to measure the duration of
an event under firmware control by reading the desired timer
at the start and at the end of an event, then calculating the
difference between the two values. The two 8-bit capture timer
registers save a programmable 8-bit range of the free-running
timer when a GPIO edge occurs on the two capture pins (P0.5,
P0.6). The two 8-bit captures can be ganged into a single
16-bit capture.
The enCoRe II includes an integrated USB serial interface
engine (SIE) that allows the chip to easily interface to a USB
host. The hardware supports one USB device address with
three endpoints.
The USB D+ and D– pins can optionally be used as PS/2
SCLK and SDATA signals so that products can be designed to
respond to either USB or PS/2 modes of operation. PS/2
operation is supported with internal 5 Kpull-up resistors on
P1.0 (D+) and P1.1 (D–) and an interrupt to signal the start of
PS/2 activity. In USB mode, the integrated 1.5 Kpull-up
resistor on D– can be controlled under firmware. No external
components are necessary for dual USB and PS/2 systems,
and no GPIO pins need to be dedicated to switching between
modes.
The enCoRe II supports in-system programming by using the
D+ and D– pins as the serial programming mode interface.
The programming protocol is not USB.
3.0 Conventions
In this document, bit positions in the registers are shaded to
indicate which members of the enCoRe II family implement the
bits.
Available in all enCoRe II family members
CY7C638xx only
Document 38-08035 Rev. *I
Page 2 of 74
[+] Feedback



Cypress Semiconductor CY7C63801
4.0 Logic Block Diagram
Figure 4-1. CY7C63310/CY7C638xx Block Diagram
CY7C63310
CY7C638xx
www.DataSheet4U.com
3.3V
Regulator
Low-Speed
USB/PS2
Transceiver
and Pull-up
Low-Speed
USB SIE
Interrupt
Control
4 3VIO/SPI
Pins
Up to 14
Extended
I/O Pins
Up to 6
GPIO
pins
Wakeup
Timer
Internal
24 MHz
Oscillator
External Clock
Clock
Control
POR /
Low-Voltage
Detect
M8C CPU
Watchdog
Timer
RAM
Up to 256
Byte
Flash
Up to 8K
Byte
12-bit Timer
16-bit Free
running
timer
Document 38-08035 Rev. *I
Page 3 of 74
[+] Feedback







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)