SERVICE MANUAL. STR-K675P Datasheet

STR-K675P MANUAL. Datasheet pdf. Equivalent

Part STR-K675P
Description FM STEREO FM-AM RECEIVER SERVICE MANUAL
Feature SERVICE MANUAL Ver. 1.0 2005.03 STR-K675P US Model • STR-K675P is the tuner and the amplifier sect.
Manufacture Sony
Datasheet
Download STR-K675P Datasheet

SERVICE MANUAL Ver. 1.0 2005.03 STR-K675P US Model • STR-K STR-K675P Datasheet
Recommendation Recommendation Datasheet STR-K675P Datasheet




STR-K675P
SERVICE MANUAL
Ver. 1.0 2005.03
STR-K675P
US Model
• STR-K675P is the tuner and the amplifier
section in HT-DDW675.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks
of Dolby Laboratories.
“DTS” and “DTS Digital Surround” are registered trademarks of
Digital Theater Systems, Inc.
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS Inputs (Digital)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(Models of area code US only)
With 6 ohm loads, both channels driven, from
120 – 20,000 Hz; rated 70 watts per channel
minimum RMS power, with no more than 0.7%
total harmonic distortion from 250 milliwatts to
rated output.
DVD (Coaxial)
SA-CD/CD (Optical)
Output (Analog)
SUB WOOFER
Sensitivity: –
Impedance: 75 ohms
Sensitivity: –
Impedance: –
Voltage: 2 V
Impedance: 1 k ohm
Amplifier section
Power Output1)
(6 ohms 1 kHz, THD 10%)
FRONT2):
110 W/ch
CENTER2):
110 W
SURR2):
110 W/ch
1) Measured under the following conditions:
120 V AC, 60 Hz
2) Depending on the sound field settings and the
source, there may be no sound output.
Inputs (Analog)
SA-CD/CD, DVD
VIDEO 1, 2
Sensitivity: 800 mV
Impedance: 50 k ohms
Reproduction frequency range:
28 – 20,000 Hz
Tone
Gain levels
±6 dB, 1 dB step
FM tuner section
Tuning range
Antenna
Antenna terminals
Intermediate frequency
87.5 - 108.0 MHz
FM wire antenna
75 ohms, unbalanced
10.7 MHz
AM tuner section
Tuning range
With 10-kHz tuning scale: 530 - 1,710 kHz3)
With 9-kHz tuning scale: 531 - 1,710 kHz3)
Antenna
Loop antenna
Intermediate frequency 450 kHz
3) You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off the
receiver. While holding down PRESET TUNING +
or TUNING +, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the procedure.
General
Power requirements
Power consumption
120 V AC, 60 Hz
170 W
Power consumption (during standby mode)
0.2 W
Dimensions (w/h/d) (Approx.)
430 × 145 × 301.5 mm
(17 × 5 6/8 × 11 7/8 inches)
including projecting parts
and controls
Mass (Approx.)
6.5 kg (14 lb 6 oz)
Design and specifications are subject to change
without notice
9-879-446-01
2005C1678-1
© 2005.03
Sony Corporation
Audio Group
Published by Sony Engineering Corporation
FM STEREO FM-AM RECEIVER



STR-K675P
STR-K675P
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
To Exposed Metal
Parts on Set
0.15 µF
1.5 k
AC
voltmeter
(0.75 V)
TABLE OF CONTENTS
1. GENERAL ................................................................... 3
2. TEST MODE ............................................................... 7
3. DIAGRAMS
3-1. Block Diagram — MAIN Section — .............................. 10
3-2. Block Diagram — DISPLAY/POWER Section — ........ 11
3-3. Printed Wiring Board
— DIGITAL Board (Side A) — ...................................... 12
3-4. Printed Wiring Board
— DIGITAL Board (Side B) — ...................................... 13
3-5. Schematic Diagram — DIGITAL Board (1/4) — .......... 14
3-6. Schematic Diagram — DIGITAL Board (2/4) — .......... 15
3-7. Schematic Diagram — DIGITAL Board (3/4) — .......... 16
3-8. Schematic Diagram — DIGITAL Board (4/4) — .......... 17
3-9. Printed Wiring Board — MAIN Section — ................... 18
3-10. Schematic Diagram — MAIN Section (1/3) — ............. 19
3-11. Schematic Diagram — MAIN Section (2/3) — ............. 20
3-12. Schematic Diagram — MAIN Section (3/3) — ............. 21
3-13. Printed Wiring Board — STANDBY Section — ........... 22
3-14. Printed Wiring Board — DISPLAY Section — ............. 23
3-15. Schematic Diagram — DISPLAY Section — ................ 24
3-16. Printed Wiring Board — VIDEO Board — .................... 25
3-17. Schematic Diagram — VIDEO Board — ...................... 26
4. EXPLODED VIEWS
4-1. Front Panel Section ......................................................... 34
4-2. Chassis Section ................................................................ 35
5. ELECTRICAL PARTS LIST .................................. 36
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
Notes on chip component replacement
Never reuse a disconnected chip component.
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)