X40011 Monitor Datasheet

X40011 Datasheet, PDF, Equivalent


Part Number

X40011

Description

Dual Voltage Monitor

Manufacture

Renesas

Total Page 24 Pages
Datasheet
Download X40011 Datasheet


X40011
DATASHEET
X40010, X40011, X40014, X40015
Dual Voltage Monitor with Integrated CPU Supervisor
FN8111
Rev 0.00
March 28, 2005
FEATURES
• Dual voltage detection and reset assertion
—Standard reset threshold settings
See Selection table on page 2.
—Adjust low voltage reset threshold voltages
using special programming sequence
—Reset signal valid to VCC = 1V
—Monitor three voltages or detect power fail
• Independent Core Voltage Monitor (V2MON)
• Fault detection register
• Selectable power on reset timeout (0.05s,
0.2s, 0.4s, 0.8s)
• Selectable watchdog timer interval (25ms,
200ms,1.4s, off)
• Low power CMOS
—25µA typical standby current, watchdog on
—6µA typical standby current, watchdog off
• 400kHz 2-wire interface
• 2.7V to 5.5V power supply operation
• Available packages
—8-lead SOIC, TSSOP
• Monitor Voltages: 5V to 0.9V
• Independent Core Voltage Monitor
APPLICATIONS
• Communication Equipment
—Routers, Hubs, Switches
—Disk Arrays, Network Storage
• Industrial Systems
—Process Control
—Intelligent Instrumentation
• Computer Systems
— Computers
—Network Servers
DESCRIPTION
The X40010/11/14/15 combines power-on reset con-
trol, watchdog timer, supply voltage supervision, and
secondary voltage supervision, in one package. This
combination lowers system cost, reduces board space
requirements, and increases reliability.
Applying voltage to VCC activates the power on reset
circuit which holds RESET/RESET active for a period of
time. This allows the power supply and system oscilla-
tor to stabilize before the processor can execute code.
BLOCK DIAGRAM
SDA
SCL
VCC
(V1MON)
V2MON
Data
Register
Command
Decode Test
& Control
Logic
Threshold
Reset Logic
Fault Detection
Register
Status
Register
Watchdog Timer
and
Reset Logic
User Programmable
VTRIP1
User Programmable
VTRIP2
+
-
V2MON
+ VCC
Power on,
Low Voltage
Reset
Generation
-
*X40010/11 = V2MON*
X40014/15 = VCC
WDO
RESET
X40010/14
RESET
X40011/15
V2FAIL
FN8111 Rev 0.00
March 28, 2005
Page 1 of 24

X40011
X40010, X40011, X40014, X40015
Low VCC detection circuitry protects the user’s system
from low voltage conditions, resetting the system when
VCC falls below the minimum VTRIP1 point.
RESET/RESET is active until VCC returns to proper
operating level and stabilizes. A second voltage monitor
circuit tracks the unregulated supply to provide a power
fail warning or monitors different power supply voltage.
Three common low voltage combinations are available,
however, Intersil’s unique circuits allows the threshold
for either voltage monitor to be reprogrammed to meet
special needs or to fine-tune the threshold for applica-
tions requiring higher precision.
The Watchdog Timer provides an independent protec-
tion mechanism for microcontrollers. When the micro-
controller fails to restart a timer within a selectable time
out interval, the device activates the WDO signal. The
user selects the interval from three preset values. Once
selected, the interval does not change, even after
cycling the power.
The device features a 2-wire interface and software pro-
tocol allowing operation on an I2C® bus.
Dual Voltage Monitors
Device
X40010/11
-A
-B
-C
X40014/15
-A
-B
-C
Expected System Voltages
5V; 3V or 3.3V
5V; 3V
3V; 3.3V; 1.8V
3V; 3.3V; 1.5V
3V; 1.5V
3V or 3.3V; 1.1 or 1.2V
Table 1:
Vtrip1(V)
2.0–4.75*
4.55–4.65*
4.35–4.45*
2.85–2.95*
2.0–4.75*
2.85–2.95*
2.55–2.65*
2.85–2.95*
Vtrip2(V)
1.70–4.75
2.85–2.95
2.55–2.65
1.65–1.75
0.90–3.50*
1.25–1.35*
1.25–1.35*
0.95–1.05*
POR (system)
RESET = X40010
RESET = X40011
RESET = X40014
RESET = X40015
*Voltage monitor requires VCC to operation. Others are independent of VCC.
PIN CONFIGURATION
X40010/14, X40011/15
8-Pin SOIC
V2FAIL
V2MON
RESET/RESET
VSS
1
2
3
4
8 VCC
7 WDO
6 SCL
5 SDA
PIN DESCRIPTION
X40010/14, X40011/15
8-Pin TSSOP
WDO
VCC
V2FAIL
V2MON
1
2
3
4
8 SCL
7 SDA
6 VSS
5 RESET/RESET
Pin
SOIC TSSOP Name
Function
1 3 V2FAIL V2 Voltage Fail Output. This open drain output goes LOW when V2MON is less than VTRIP2 and
goes HIGH when V2MON exceeds VTRIP2. There is no power up reset delay circuitry on this pin.
2 4 V2MON V2 Voltage Monitor Input. When the V2MON input is less than the VTRIP2 voltage, V2FAIL goes
LOW. This input can monitor an unregulated power supply with an external resistor divider or can
monitor a second power supply with no external components. Connect
not used.The V2MON comparator is supplied by V2MON (X40010/11)
V2MON to VSS
or by VCC Input
(oXr4V0C0C14w/1h5e)n.
3 5 RESET/ RESET Output. (X40011/15) This is an active LOW, open drain output which goes active whenever
RESET VCC falls below VTRIP1. It will remain active until VCC rises above VTRIP1 and for the tPURST thereafter.
RESET Output. (X40010/14) This is an active HIGH CMOS output which
falls below VTRIP1. It will remain active until VCC rises above VTRIP1 and
goes active whenever VCC
for the tPURST thereafter.
4 6 VSS Ground
5 7 SDA Serial Data. SDA is a bidirectional pin used to transfer data into and out of the device. It has an open
drain output and may be wire ORed with other open drain or open collector outputs. This pin requires
a pull up resistor and the input buffer is always active (not gated).
Watchdog Input. A HIGH to LOW transition on the SDA (while SCL is toggled from HIGH to
LOW and followed by a stop condition) restarts the Watchdog timer. The absence of this transi-
tion within the watchdog time out period results in WDO going active.
FN8111 Rev 0.00
March 28, 2005
Page 2 of 24


Features DATASHEET X40010, X40011, X40014, X4001 5 Dual Voltage Monitor with Integrated CPU Supervisor FN8111 Rev 0.00 March 2 8, 2005 FEATURES • Dual voltage dete ction and reset assertion —Standard r eset threshold settings See Selection t able on page 2. —Adjust low voltage r eset threshold voltages using special p rogramming sequence —Reset signal val id to VCC = 1V —Monitor three voltage s or detect power fail • Independent Core Voltage Monitor (V2MON) • Fault detection register • Selectable power on reset timeout (0.05s, 0.2s, 0.4s, 0 .8s) • Selectable watchdog timer inte rval (25ms, 200ms,1.4s, off) • Low po wer CMOS —25µA typical standby curre nt, watchdog on —6µA typical standby current, watchdog off • 400kHz 2-wir e interface • 2.7V to 5.5V power supp ly operation • Available packages — 8-lead SOIC, TSSOP • Monitor Voltages : 5V to 0.9V • Independent Core Volta ge Monitor APPLICATIONS • Communicat ion Equipment —Routers, Hubs, Switches —Disk Arrays, Networ.
Keywords X40011, datasheet, pdf, Renesas, Dual, Voltage, Monitor, 40011, 0011, 011, X4001, X400, X40, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)