RRIO Op-amps. TP2411 Datasheet

TP2411 Op-amps. Datasheet pdf. Equivalent

TP2411 Datasheet
Recommendation TP2411 Datasheet
Part TP2411
Description Low Noise CMOS RRIO Op-amps
Feature TP2411; 3PEAK Features  Gain-bandwidth Product: 10 MHz  Low Noise: 8.2 nV/√Hz(f= 1kHz)  Slew Rate: 7 V/μs.
Manufacture 3PEAK
Datasheet
Download TP2411 Datasheet




3PEAK TP2411
3PEAK
Features
Gain-bandwidth Product: 10 MHz
Low Noise: 8.2 nV/√Hz(f= 1kHz)
Slew Rate: 7 V/μs
Offset Voltage: 1 mV (max)
EMIRR IN+: 88 dB( under 2.4GHz)
Low THD+N: 0.0005%
Supply Range: 2.2 V to 5.5 V
Supply Current: 1.4 mA/ch
Low Input Bias Current: 0.3pA Typical
Rail-to-Rail I/O
High Output Current: 70 mA (1.0V Drop)
40°C to 125°C Operation Range
Applications
Sensor Signal Conditioning
Consumer Audio
Multi-Pole Active Filters
Control-Loop Amplifiers
Communications
Security
Scanners
TP2411/TP2412 /TP2414
Low Cost, Low Noise CMOS RRIO Op-amps
Description
The TP2411, TP2412, and TP2414 are low cost, single,
dual, and quad rail-to-rail output, single-supply amplifiers
featuring low offset and input voltages, low current noise,
and wide signal bandwidth. The combination of low
offset, low noise, very low input bias currents, and high
speed make these amplifiers useful in a wide variety of
applications. Filters, integrators, photodiode amplifiers,
and high impedance sensors all benefit from this
combination of performance features. Audio and other
ac applications benefit from the wide bandwidth and low
distortion of these devices.
Applications for these amplifiers include power
amplifier (PA) controls, laser diode control loops,
portable and loop-powered instrumentation, audio
amplification for portable devices, and ASIC input and
output amplifiers.
The TP2411 is single channel version available in 8-pin
SOP and 5-pin SOT23 packages. The TP2412 is dual
channel version available in 8-pin SOP, SOT, TSSOP
and MSOP packages. The TP2414 is quad channel
version available in 14-pin SOP and TSSOP packages.
3PEAK and the 3PEAK logo are registered trademarks of
3PEAK INCORPORATED. All other trademarks are the property of
their respective owners.
Pin Configuration (Top View)
TP2411
8-Pin SOP
(-S Suffix)
NC 1
In 2
In 3
Vs 4
8 NC
7 Vs
6 Out
5 NC
TP2412
8-Pin SOP/MSOP/SOT/TSSOP
(-S ,-V, -T, -TS Suffixes)
Out A 1
In A 2
In A 3
Vs 4
A
B
8 Vs
7 Out B
6 In B
5 In B
TP2411
5-Pin SOT23
(-T Suffix)
Out
Vs
+In
1
2
3
5 Vs
4 -In
TP2414
14-Pin SOP/TSSOP
(-S and -T Suffixes)
Out A 1
In A 2
In A 3
Vs 4
In B 5
In B 6
Out B 7
A
B
14 Out D
13 In D
D
12 In D
11 Vs
10 In C
C
9 In C
8 Out C
Input Voltage Noise Spectral Density
1000
VCC= +5V
RL= 1kΩ
100
10
1
1 10 100 1k 10k 100k 1M
Frequency(Hz)
www.3peakic.com.cn
Rev. B.01
1



3PEAK TP2411
TP2411 / TP2412 / TP2414
Low Cost, Low Noise CMOS RRIO Op-amps
Order Information
Model Name
TP2411
TP2412
TP2414
Order Number
TP2411-SR
TP2411-TR
TP2412-SR
TP2412-VR
TP2412-TSR
TP2412-TR
TP2414-SR
TP2414-TR
Package
8-Pin SOP
5-Pin SOT23
8-Pin SOP
8-Pin MSOP
8-Pin TSSOP
8-Pin SOT23
14-Pin SOP
14-Pin TSSOP
Absolute Maximum Ratings Note 1
Transport Media, Quantity
Tape and Reel, 4,000
Tape and Reel, 3,000
Tape and Reel, 4,000
Tape and Reel, 3,000
Tape and Reel, 3,000
Tape and Reel, 3,000
Tape and Reel, 2,500
Tape and Reel, 3,000
Marking
Information
TP2411
411
TP2412
TP2412
TP2412
S12
TP2414
TP2414
Supply Voltage: V+ VNote 2............................7.0V
Input Voltage............................. V0.3 to V+ + 0.3
Input Current: +IN, IN Note 3.......................... ±20mA
Output Short-Circuit Duration Note 4......... Indefinite
Current at Supply Pins……………............... ±60mA
Operating Temperature Range........40°C to 125°C
Maximum Junction Temperature................... 150°C
Storage Temperature Range.......... 65°C to 150°C
Lead Temperature (Soldering, 10 sec) ......... 260°C
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum
Rating condition for extended periods may affect device reliability and lifetime.
Note 2: The op amp supplies must be established simultaneously, with, or before, the application of any input signals.
Note 3: The inputs are protected by ESD protection diodes to each power supply. If the input extends more than 500mV beyond the power supply, the input
current should be limited to less than 10mA.
Note 4: A heat sink may be required to keep the junction temperature below the absolute maximum. This depends on the power supply voltage and how many
amplifiers are shorted. Thermal resistance varies with the amount of PC board metal connected to the package. The specified values are for short traces
connected to the leads.
ESD, Electrostatic Discharge Protection
Symbol
HBM
CDM
Parameter
Human Body Model ESD
Charged Device Model ESD
Condition
ANSI/ESDA/JEDEC JS-001
ANSI/ESDA/JEDEC JS-002
Minimum Level
2
1
Unit
kV
kV
Thermal Resistance
Package Type
5-Pin SOT23
8-Pin SOP
8-Pin MSOP
8-Pin TSSOP
8-Pin SOT23
14-Pin SOP
14-Pin TSSOP
θJA
250
158
210
191
196
120
180
θJC
81
43
45
70
36
35
Unit
° C/W
° C/W
° C/W
° C/W
° C/W
° C/W
° C/W
2 Rev. B.01
www.3peakic.com.cn



3PEAK TP2411
TP2411/TP2412 / TP2414
Electrical Characteristics
Low Cost, Low Noise CMOS RRIO Op-amps
The specifications are at TA = 27° C. VS = 5V, RL = 2kΩ, CL =100pF.Unless otherwise noted.
SYMBOL
PARAMETER
VOS
VOS TC
Input Offset Voltage
Input Offset Voltage Drift
IB Input Bias Current
IOS Input Offset Current
Vn Input Voltage Noise
en Input Voltage Noise Density
in Input Current Noise
CIN Input Capacitance
CMRR Common Mode Rejection Ratio
VCM
PSRR
AVOL
VOL, VOH
ROUT
RO
ISC
VS
IQ
PM
GM
GBWP
SR
FPBW
tS
THD+N
Xtalk
Common-mode Input Voltage
Range
Power Supply Rejection Ratio
Open-Loop Large Signal Gain
Output Swing from Supply Rail
Closed-Loop Output Impedance
Open-Loop Output Impedance
Output Short-Circuit Current
Supply Voltage
Quiescent Current per Amplifier
Phase Margin
Gain Margin
Gain-Bandwidth Product
Slew Rate
Full Power Bandwidth Note 1
Settling Time, 0.1%
Settling Time, 0.01%
Total Harmonic Distortion and
Noise
Channel Separation
CONDITIONS
VCM = VS/2
VCM = 0V
-40° C to 125° C
TA = 27 ° C
TA = 85 ° C
TA = 125 ° C
MIN
-1
-1
f = 0.1Hz to 10Hz
f = 1kHz
f = 1kHz
Differential
Common Mode
VCM = 2.5V
VCM = 0V to 3V
VCM = 0V to 5V
VS = 2.2V to 5.5V, VCM = 0V
RLOAD = 2kΩ, VOUT = -2V to 2V
RLOAD = 2kΩ
G = 1, f =1MHz, IOUT = 0
f = 1kHz, IOUT = 0
Sink or source current
VS = 5V
RLOAD = 1kΩ, CLOAD = 60pF
RLOAD = 1kΩ, CLOAD = 60pF
f = 1kHz
AV = 1, VOUT = 0V to 10V, CLOAD = 100pF,
RLOAD = 2
90
80
55
V-0.1
82
100
100
2.2
3.0
AV = 1, 1V Step
f = 1kHz, AV =1, RL = 2kΩ, VOUT = 1Vp-p
f = 1kHz, RL = 2
TYP
± 0.25
± 0.25
1
0.3
150
300
0.3
3.14
8.2
2
8
7
106
106
72
100
120
20
0.2
125
130
1.4
60
8
10
7
414
0.75
0.85
0.0005
110
MAX
+1
+1
V+-0.1
50
5.5
1.95
UNITS
mV
mV
μV/° C
pA
pA
pA
pA
μVPP
nV/√Hz
fA/√Hz
pF
dB
dB
dB
V
dB
dB
mV
Ω
Ω
mA
V
mA
°
dB
MHz
V/μs
kHz
μs
%
dB
Note 1: Full power bandwidth is calculated from the slew rate FPBW = SR/π • VP-P
www.3peakic.com.cn
Rev. B.01
3







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)