DatasheetsPDF.com

SAW Filter. SF2315E Datasheet

DatasheetsPDF.com

SAW Filter. SF2315E Datasheet






SF2315E Filter. Datasheet pdf. Equivalent




SF2315E Filter. Datasheet pdf. Equivalent





Part

SF2315E

Description

SAW Filter



Feature


• Low-loss 782 MHz SAW Filter • Desi gned for 50 ohm Source/Load Absolute Ma ximum Ratings Rating Input Power Level DC Voltage on any Non-ground Terminal O perating Temperature Range Storage Temp erature Range in Tape and Reel Maximum Soldering Profile, 5 cycles/10 seconds maximum Value +25 3 -40 to +85 -40 to +85 265 Units dBm V °C °C °C RoHS Compliance This component.
Manufacture

muRata

Datasheet
Download SF2315E Datasheet


muRata SF2315E

SF2315E; is compliant with RoHS directive. This component was always RoHS compliant fro m the first date of manufacture. SF2315 E 782 MHz SAW Filter Electrical Charac teristics Characteristic Center Frequ ency Insertion Loss, 777 to 787 MHz B andwidth Amplitude Ripple, 777 to 787 MHz Attenuation, Referenced to 0 dB: 3 00 to 700 MHz 728 to 757 MHz 880 to 1 050 MHz Source Im.


muRata SF2315E

pedance Load Impedance Case Style Lid Symbolization (Y=year, WW=week, S=shif t) dot=pin 1 indicator Standard Reel Q uantity Reel Size 7 inch Reel Size 13 inch Electrical Connections Connecti on Terminals Input 2 Output 5 Cas e Ground All othe .


muRata SF2315E

.

Part

SF2315E

Description

SAW Filter



Feature


• Low-loss 782 MHz SAW Filter • Desi gned for 50 ohm Source/Load Absolute Ma ximum Ratings Rating Input Power Level DC Voltage on any Non-ground Terminal O perating Temperature Range Storage Temp erature Range in Tape and Reel Maximum Soldering Profile, 5 cycles/10 seconds maximum Value +25 3 -40 to +85 -40 to +85 265 Units dBm V °C °C °C RoHS Compliance This component.
Manufacture

muRata

Datasheet
Download SF2315E Datasheet




 SF2315E
• Low-loss 782 MHz SAW Filter
• Designed for 50 ohm Source/Load
Absolute Maximum Ratings
Rating
Input Power Level
DC Voltage on any Non-ground Terminal
Operating Temperature Range
Storage Temperature Range in Tape and Reel
Maximum Soldering Profile, 5 cycles/10 seconds maximum
Value
+25
3
-40 to +85
-40 to +85
265
Units
dBm
V
°C
°C
°C
RoHS Compliance
This component is compliant
with RoHS directive.
This component was always
RoHS compliant from the first
date of manufacture.
SF2315E
782 MHz
SAW Filter
Electrical Characteristics
Characteristic
Center Frequency
Insertion Loss, 777 to 787 MHz
Bandwidth
Amplitude Ripple, 777 to 787 MHz
Attenuation, Referenced to 0 dB:
300 to 700 MHz
728 to 757 MHz
880 to 1050 MHz
Source Impedance
Load Impedance
Case Style
Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator
Standard Reel Quantity
Reel Size 7 inch
Reel Size 13 inch
Electrical Connections
Connection
Terminals
Input
2
Output
5
Case Ground
All others
SM3030-6
Sym Notes
Min
Typ
Max
fC 782
IL 2.2 3.0
10 25
0.35 1.00
28 61
10 48
28 61
ZS 50
ZL 50
SM3030-6 3.0 x 3.0 mm Nominal Footprint
A72, YWWS
500 Pieces/Reel
3000 Pieces/Reel
Units
MHz
dB
MHz
dBP-P
dB
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
NOTES:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance
matching to 50 and measured with 50 network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external
impedance matching design. See Application Note No. 42 for details.
4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port
2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd.
Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 2012
SF2315E (R) 1/4/19
Page 1 of 4
www.murata.com




 SF2315E
Filter Response Plots
Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 2012
SF2315E (R) 1/4/19
Page 2 of 4
www.murata.com




 SF2315E
SM3030-6 Case
6-Terminal Ceramic Surface-Mount Case
3.0 X 3.0 mm Nominal Footprint
K
L
N
KN
O
N
MM
PCB Footprint Top View
Case and PCB Footprint Dimensions
Dimension
Min
mm
Nom
Max
Min
A 2.87 3.00 3.13 0.113
B 2.87 3.00 3.13 0.113
C 1.12 1.25 1.38 0.044
D 0.77 0.90 1.03 0.030
E 2.67 2.80 2.93 0.105
F 1.47 1.60 1.73 0.058
G 0.72 0.85 0.98 0.028
H 1.37 1.50 1.63 0.054
I 0.47 0.60 0.73 0.019
J 1.17 1.30 1.43 0.046
K 3.20
L 1.70
M 1.05
N 0.81
O 0.38
P 0.15 0.30 0.45 0.005
Q 0.07 0.20 0.36 0.002
R 0.62 0.7 0.78 0.024
Case Materials
Inches
Nom
0.118
0.118
0.049
0.035
0.110
0.063
0.033
0.059
0.024
0.051
0.126
0.067
0.041
0.032
0.015
0.011
0.007
0.027
Max
0.123
0.123
0.054
0.040
0.115
0.068
0.038
0.064
0.029
0.056
0.017
0.014
0.030
Solder Pad
Plating
Materials
0.3 to 1.0 µm Gold over 1.27 to 8.89 µm Nickel
Lid Plating
2.0 to 3.0 µm Nickel
Body
Al2O3 Ceramic
Pb Free
Q
P
R
Q
Copyright © Murata Manufacturing Co., Ltd. All rights reserved. 2012
SF2315E (R) 1/4/19
Page 3 of 4
www.murata.com



Recommended third-party SF2315E Datasheet






@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)