TSOP98336 Modules Datasheet

TSOP98336 Datasheet PDF, Equivalent


Part Number

TSOP98336

Description

IR Receiver Modules

Manufacture

Vishay

Total Page 8 Pages
PDF Download
Download TSOP98336 Datasheet PDF


TSOP98336
www.vishay.com
TSOP983.., TSOP985..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
1
2
3
FEATURES
• Improved dark sensitivity
• Improved immunity against optical noise
• Very low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Supply voltage: 2.5 V to 3.6 V
• Material categorization:
for definitions of compliance please see
19026
www.vishay.com/doc?99912
DESIGN SUPPORT TOOLS click logo to get started
Models
Available
MECHANICAL DATA
1 = OUT, 2 = GND, 3 = VS
DESCRIPTION
The TSOP98... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems.
This series provides improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence
of optical disturbances e.g. from CFLs.
The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The
demodulated output signal can be directly connected to a microprocessor for decoding.
The TSOP983.. and TSOP985.. series devices are designed to receive short burst codes (6 or more carrier cycles per burst).
The third digit designates the AGC level (AGC3 or AGC5) and the last two digits designate the band-pass frequency (see table
below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC3 provides enhanced
noise suppression and AGC5 provides maximized noise suppression. Generally, we advise to select the highest AGC that
satisfactorily receives the desired remote code.
These components have not been qualified to automotive specifications.
PARTS TABLE
AGC
Carrier frequency
Package
Pinning
Dimensions (mm)
Mounting
Application
Best choice for
30 kHz
33 kHz
36 kHz
38 kHz
40 kHz
56 kHz
ENHANCED NOISE SUPPRESSION
(AGC3)
MAXIMIZED NOISE SUPPRESSION
(AGC5)
TSOP98330
TSOP98530
TSOP98333
TSOP98533
TSOP98336 (1)
TSOP98536
TSOP98338 (2)(4)
TSOP98538
TSOP98340
TSOP98540
TSOP98356
TSOP98556 (3)
Minicast
1 = OUT, 2 = GND, 3 = VS
5.0 W x 6.95 H x 4.8 D
Leaded
Remote control
(1) RCMM (2) RECS-80 Code (3) r-map (4) XMP-1, XMP-2
Note
• 30 kHz and 33 kHz only available on written request
Rev. 1.2, 11-Dec-2018
1 Document Number: 82833
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TSOP98336
www.vishay.com
BLOCK DIAGRAM
16833-13
30 kΩ
Input
AGC
Band
pass
Demo-
dulator
PIN Control circuit
3
1
2
TSOP983.., TSOP985..
Vishay Semiconductors
APPLICATION CIRCUIT
17170-12
Transmitter
with
TSALxxxx
IR receiver
VS
OUT
GND
R1
C1
VO
+ VS
μC
GND
R1 and C1 recommended to reduce supply ripple for VS < 2.2 V
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
Supply voltage
Supply current
VS -0.3 to +3.6
V
IS 3 mA
Output voltage
VO -0.3 to (VS + 0.3)
V
Output current
Junction temperature
IO 5 mA
Tj 100 °C
Storage temperature range
Tstg -25 to +85
°C
Operating temperature range
Power consumption
Soldering temperature
Tamb 85 °C
t 10 s, 1 mm from case
Tamb
Ptot
Tsd
-25 to +85
10
260
°C
mW
°C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL MIN.
TYP.
MAX.
Supply current
Supply voltage
Transmission distance
Output voltage low
Minimum irradiance
Ev = 0, VS = 3.3 V
Ev = 40 klx, sunlight
Ev = 0, test signal see Fig. 1,
IR diode TSAL6200, IF = 50 mA
IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1
Test signal: XMP code
Test signal: NEC code
ISD
ISH
VS
d
VOSL
Ee min.
0.25
-
2.0
-
-
-
-
0.37
0.50
-
21
-
0.20
0.15
0.45
-
3.6
-
100
0.40
0.30
Maximum irradiance
Directivity
tpi - 3.0/f0 < tpo < tpi + 3.5/f0, test signal see Fig. 1
Angle of half transmission distance
Ee max.
ϕ1/2
30
-
-
± 45
-
-
UNIT
mA
mA
V
m
mV
mW/m2
W/m2
°
Rev. 1.2, 11-Dec-2018
2 Document Number: 82833
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000


Features www.vishay.com TSOP983.., TSOP985.. Vis hay Semiconductors IR Receiver Modules for Remote Control Systems 1 2 3 FEA TURES • Improved dark sensitivity Improved immunity against optical no ise • Very low supply current • P hoto detector and preamplifier in one p ackage • Internal filter for PCM fre quency • Supply voltage: 2.5 V to 3. 6 V • Material categorization: for definitions of compliance please see 1 9026 www.vishay.com/doc?99912 DESIGN SUPPORT TOOLS click logo to get started Models Available MECHANICAL DATA 1 = OUT, 2 = GND, 3 = VS DESCRIPTION The T SOP98... series devices are the latest generation miniaturized IR receiver mod ules for infrared remote control system s. This series provides improvements in sensitivity to remote control signals in dark ambient as well as in sensitivi ty in the presence of optical disturban ces e.g. from CFLs. The devices contain a PIN diode and a preamplifier assembl ed on a lead frame. The epoxy package contains an IR filter. The demodulated .
Keywords TSOP98336, datasheet, pdf, Vishay, IR, Receiver, Modules, SOP98336, OP98336, P98336, TSOP9833, TSOP983, TSOP98, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)