VLF252010MT-CA INDUCTORS Datasheet

VLF252010MT-CA Datasheet, PDF, Equivalent


Part Number

VLF252010MT-CA

Description

INDUCTORS

Manufacture

TDK

Total Page 9 Pages
Datasheet
Download VLF252010MT-CA Datasheet


VLF252010MT-CA
INDUCTORS
June 2017
Inductors for Power Circuits
Wound Ferrite
VLF-M-CA Series (For automobiles)
VLF252010MT-CA Type
VLF252010MT-CA
Caution
May 18, 2017
Mar. 29, 2019
Sep. 30, 2019

VLF252010MT-CA
INDUCTORS
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
(2/9)
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20170612 / inductor_automotive_power_vlf252010mt-ca_en.fm


Features INDUCTORS June 2017 Inductors for Power Circuits Wound Ferrite VLF-M-CA Series (For automobiles) VLF252010MT-CA Type V LF252010MT-CA Caution May 18, 2017 Mar. 29, 2019 Sep. 30, 2019 INDUCTORS REMI NDERS FOR USING THESE PRODUCTS Before u sing these products, be sure to request the delivery specifications. SAFETY RE MINDERS Please pay sufficient attention to the warnings for safe designing whe n using these products. (2/9) REMINDE RS The storage period is less than 12 months. Be sure to follow the storage c onditions (Temperature: 5 to 40°C, Hum idity: 10 to 75% RH or less). If the st orage period elapses, the soldering of the terminal electrodes may deteriorate . Do not use or store in locations wher e there are conditions such as gas corr osion (salt, acid, alkali, etc.). Befor e soldering, be sure to preheat compone nts. The preheating temperature should be set so that the temperature differen ce between the solder temperature and c hip temperature does not exceed 150°C. Soldering corrections aft.
Keywords VLF252010MT-CA, datasheet, pdf, TDK, INDUCTORS, LF252010MT-CA, F252010MT-CA, 252010MT-CA, VLF252010MT-C, VLF252010MT-, VLF252010MT, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)