Alternator regulator. TC80310 Datasheet

TC80310 regulator. Datasheet pdf. Equivalent

Part TC80310
Description Alternator regulator
Feature NXP Semiconductors Data Sheet: Advance Information Alternator regulator with LIN The 80310 is an int.
Manufacture NXP
Datasheet
Download TC80310 Datasheet




TC80310
NXP Semiconductors
Data Sheet: Advance Information
Alternator regulator with LIN
The 80310 is an integrated circuit intended to regulate the output voltage of an
automotive alternator.
The IC supplies a current via a high-side MOSFET to the excitation coil of the
alternator and provides an internal freewheeling diode. It keeps the battery at its
nominal charge and delivers current to electrical devices within the vehicle.
The 80310 also provides a load response control mechanism (LRC), and has
an interface for the industry standard LIN protocol (Revision 1.3) to allow an
ECU to control the regulated voltage and the LRC rate among other parameters.
The ECU also can read back information about the status of the regulator and
the alternator via LIN.
It can be programmed for most functions using OTP (Non-volatile memory) and
fit a large number of alternators and applications.
Document Number: TC80310
Rev. 5.0, 8/2016
80310
AUTOMOTIVE ALTERNATOR
REGULATOR
Features
• High-side field driver
• Internal freewheeling diode
• Up to 8.0 A rotor current (excitation coil)
• Load response control (LRC)
• Thermal protection
• Thermal compensation
• LIN interface
• Set point voltage selectable from 10.6 to 16 V
• Rotor control and die temperature monitoring via LIN
TOP VIEW
Ordering information
Device
Temperature
range (TJ)
Package
Devices part numbers are dependant on programming from
factory.
TO3 - Contact sales for information on limited engineering
sample quantities. Production version is die sales only.
Stator
Rotor
Coil
1.5 μF/2.2 μF
B+A
Master
ECU
PH1
PH2
LIN
SGND
Diagnose
Control
EXC GND
+
TC80310
Battery
-
Alternator
Figure 1. 80310 simplified application diagram (LIN mode)
Stator
Rotor
Coil
1.5 μF/2.2 μF
B+A
PH1
LIN
PH2
SGND
EXC GND
+
TC80310
Battery
-
Alternator
Figure 2. 80310 simplified application diagram (standalone, self-start mode)
* This document contains certain information on a new product.
Specifications and information herein are subject to change without notice.
© 2016 NXP B.V.



TC80310
1 Device variations
Table 1. Version determined electrical parameters
Version
Self-
start
Self-
start
Thresh
old
(RPM)
Phase
sensitiv
ity (V)
Defau
lt
Regul
ation
Voltag
e (V)
Fstart
(RPM)
Fstop
(RPM
)
LRC
Rate(
s)
LRC
disabl
e
(RPM)
Crest
Regulati
on
BUS
inactivity
(s)
Defaul
t LIN
Reado
ut
Thermal
Fault
Thresho
ld (°C)
Thermal
Compens
ation
threshold
(°C)
Speci
al LIN
Featur
e
Altern
ator
pole-
pair
Slave
Addre
ss
800/
Activ
e/
Not
Activ
e
3000/
4000
0.45/
0.9/
1.35/
1.8
13.5
to 15
(100
mV
steps)
1050/
1300/
1550/
1800/
2050/
2300/
500/
650/
850/
1000
0/3/
6.4/
12.3
2400/
3000/
4000/
Never
Active /
Not
Active
T°/ 135/
1.31 / 3 Curren 145/
t 150/160
135/145/
150/160
Active/
Not
Active
6/8
A/B
2500
Versions
TO3
Activ
e
3000
0.45
14.3
800
500
3
3000
Not
active
3
Curren
t
145
145 Active 6
A
Devices part numbers are dependant on programming from factory.
TC80310AxHWS
Various configurations are available and are programmable by OTP at the NXP factory. Please contact your NXP sales representative
for further details, based on your system requirements, and solutions available. The LIN MID 0x27 is reserved for this revision.
TC80310BxHWS
Various configurations are available and are programmable by OTP at the NXP factory. Please contact your NXP sales representative
for further details, based on your system requirements, and solutions available. The LIN MID 0x27 can be used for this revision
80310
2
NXP Semiconductors







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)