SERVICE MANUAL. HCD-GNZ5D Datasheet

HCD-GNZ5D MANUAL. Datasheet pdf. Equivalent

HCD-GNZ5D Datasheet
Recommendation HCD-GNZ5D Datasheet
Part HCD-GNZ5D
Description DVD DECK RECEIVER SERVICE MANUAL
Feature HCD-GNZ5D; HCD-GNZ5D SERVICE MANUAL Ver. 1.1 2005. 12 E Model • HCD-GNZ5D is the tuner, deck, DVD and amplif.
Manufacture Sony
Datasheet
Download HCD-GNZ5D Datasheet





Sony HCD-GNZ5D
HCD-GNZ5D
SERVICE MANUAL
Ver. 1.1 2005. 12
E Model
• HCD-GNZ5D is the tuner, deck,
DVD and amplifier section in
MHC-GNZ5D.
Amplifier section
The following measured at AC 120, 220, 230 – 240 V,
50/60 Hz
Continuous RMS power output (reference)
50 + 50 watts
(6 ohms at 1 kHz, 10%
THD)
Inputs
MIC (phone jack):
sensitivity 1 mV,
impedance 10 kilohms
Outputs
VIDEO OUT (phono jack):
max. output level
1 Vp-p, unbalanced, Sync
negative, load impedance
75 ohms
DIGITAL OPTICAL OUT (Square optical connector jack,
rear panel)
Wavelength
660 nm
PHONES (stereo mini jack):
accepts headphones of
8 ohms or more
FRONT SPEAKER: Use only the supplied
speaker SS-GNZ5D
DVD
Section
Model Name Using Similar Mechanism
DVD Mechanism Type
Optical Pick-up Name
Tape Deck Model Name Using Similar Machanism
Section Tape Transport Mechanism Type
HCD-GNZ7D/GNZ8D/GNZ9D
CDM74HF-DVBU101//C
KHM-310CAB/C2NP
HCD-GNZ7D/GNZ8D/GNZ9D
CWM43FR601
SPECIFICATIONS
Disc player section
System
Compact disc and digital
audio and video system
Laser
Semiconductor laser
(DVD: λ=650 nm,
CD: λ=790 nm)
Emission duration:
continuous
Frequency response DVD (PCM 48 kHz):
2 Hz – 22 kHz (±1 dB)
CD: 2 Hz – 20 kHz (±1 dB)
Video color system format
NTSC, PAL
Tape deck section
Recording system
4-track 2-channel stereo
Frequency response 40 – 13,000 Hz (±3 dB),
using Sony TYPE I
cassette
– Continued on next page –
9-879-821-02
2005L04-1
© 2005. 12
Sony Corporation
Home Audio Division
Published by Sony Engineering Corporation
DVD DECK RECEIVER
1



Sony HCD-GNZ5D
HCD-GNZ5D
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
87.5 – 108.0 MHz
(50-kHz step)
Antenna
FM lead antenna
Antenna terminals
75 ohm unbalanced
Intermediate frequency 10.7 MHz
AM tuner section
Tuning range
530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,602 kHz (with the
interval set at 9 kHz)
Antenna
AM loop antenna
Antenna terminals
External antenna terminal
Intermediate frequency 450 kHz
General
Power requirements
Indian model:
Thai model:
Other models:
220 – 240 V AC, 50/60 Hz
220 V AC, 50/60 Hz
120 V, 220 V or 230 –
240 V AC, 50/60 Hz
Adjustable with voltage
selector
Power consumption 110 watts
Dimensions (w/h/d) (excl. speakers)
Approx. 280 × 326 × 365 mm
Mass (excl. speakers) Approx. 9 kg
Design and specifications are subject to change without
notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2



Sony HCD-GNZ5D
HCD-GNZ5D
Ver. 1.1
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270°C during re-
pairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to about
350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may also
be added to ordinary solder.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Laser component in this product is capable
of emitting radiation exceeding the limit for
Class 1.
This appliance is
claassified as a CLASS 1
LASER product. This
label is located on the
rear exterior.
Note on DMB11 board replacement
New part of EEP ROM (IC103) on the DMB11 board cannot be
used. Therefore, if the mounted DMB11 board (A-1109-317-A, etc.)
is replaced, exchange new EEP ROM (IC103) with that used before
the replacement.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
3





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)