Operational Amplifiers. HS-OP470ARH Datasheet

HS-OP470ARH Amplifiers. Datasheet pdf. Equivalent

Part HS-OP470ARH
Description Very Low Noise Quad Operational Amplifiers
Feature DATASHEET HS-OP470ARH, HS-OP470AEH Radiation Hardened, Very Low Noise Quad Operational Amplifiers .
Manufacture Intersil Corporation
Datasheet
Download HS-OP470ARH Datasheet




HS-OP470ARH
DATASHEET
HS-OP470ARH, HS-OP470AEH
Radiation Hardened, Very Low Noise Quad Operational Amplifiers
FN4471
Rev.3.00
Sep 21, 2018
The HS-OP470ARH and HS-OP470AEH are radiation hardened,
monolithic quad operational amplifiers that provide highly
reliable performance in harsh radiation environments. Excellent
noise characteristics coupled with a unique array of dynamic
specifications make these amplifiers well-suited for a variety of
satellite system applications. Dielectrically isolated, bipolar
processing makes these devices immune to single event latch-up.
The HS-OP470ARH and HS-OP470AEH show almost no change in
offset voltage after exposure to 100krad(Si) gamma radiation,
with only a minor increase in current. Complementing these
specifications is a post radiation open-loop gain in excess of
40kV/V.
These quad operational amplifiers are available in an industry
standard pinout, allowing for immediate interchangeability
with most other quad operational amplifiers.
Pin Configuration
(14 LD FLATPACK)
TOP VIEW
OUT 1
-IN1
+IN1
V+
+IN2
-IN2
OUT 2
1
2
3
4
5
6
7
14 OUT 4
13 -IN4
12 +IN4
11 V-
10 +IN3
9 -IN3
8 OUT 3
Features
• Electrically screened to SMD # 5962-98533
• QML qualified per MIL-PRF-38535 requirements
• Radiation environment
- High dose rate (50-300rad(Si)/s). . . . . . . . . . . 100krad(Si)
- Low dose rate (0.01rad(Si)/s) . . . . . . . . . . . . . . .50krad(Si)
• Low noise
- At 1kHz . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3nV/Hz (typical)
- At 1kHz . . . . . . . . . . . . . . . . . . . . . . . . . . 0.6pA/Hz (typical)
• Low offset voltage . . . . . . . . . . . . . . . . . . . 2.1mV (maximum)
• High slew rate . . . . . . . . . . . . . . . . . . . . . 1.7V/µs (minimum)
• Gain bandwidth product . . . . . . . . . . . . . . . . . 8.0MHz (typical)
Applications
• High Q, active filters
• Voltage regulators
• Integrators
• Signal generators
• Voltage references
• Space environments
Related Literature
For a full list of related documents, visit our website:
HS-OP470ARH, HS-OP470AEH product pages
FN4471 Rev.3.00
Sep 21, 2018
Page 1 of 6



HS-OP470ARH
HS-OP470ARH, HS-OP470AEH
Ordering Information
ORDERING SMD NUMBER
(Note 1)
PART NUMBER
(Note 2)
TEMP. RANGE
(°C)
PACKAGE
(RoHS Compliant)
PKG.
DWG. #
5962R9853301VXC
HS9-OP470ARH-Q
-55 to +125
14 Ld Flatpack
K14.A
5962R9853302VXC
HS9-OP470AEH-Q
-55 to +125
14 Ld Flatpack
K14.A
5962R9853301V9A
HS0-OP470ARH-Q
-55 to +125
Die
5962R9853302V9A
HS0-OP470AEH-Q
-55 to +125
Die
N/A
HS0-OP470ARH/SAMPLE (Note 3)
-55 to +125
Die
N/A
HS0-OP470AEH/SAMPLE (Note 3)
-55 to +125
Die
5962R9853301QXC
HS9-OP470ARH-8
-55 to +125
14 Ld Flatpack
K14.A
N/A
HS9-OP470ARH/PROTO (Note 3)
-55 to +125
14 Ld Flatpack
K14.A
N/A
HS9-OP470AEH/PROTO (Note 3)
-55 to +125
14 Ld Flatpack
K14.A
HS-OP470ARHEV1Z
HS-OP470ARHEV1Z (Note 4)
Evaluation Board
1. Specifications for Rad Hard QML devices are controlled by the Defense Logistics Agency Land and Maritime (DLA). The SMD numbers listed must
be used when ordering.
2. These Pb-free Hermetic packaged products employ 100% Au plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb
and Pb-free soldering operations.
3. The /PROTO and /SAMPLE are not rated or certified for Total Ionizing Dose (TID) or Single Event Effect (SEE) immunity. These parts are intended for
engineering evaluation purposes only. The /PROTO parts meet the electrical limits and conditions across the temperature range specified in the
DLA SMD and are in the same form and fit as the qualified device. The /SAMPLE die is capable of meeting the electrical limits and conditions
specified in the DLA SMD at +25°C only. The /SAMPLE is a die and does not receive 100% screening across the temperature range to the DLA SMD
electrical limits. These part types do not come with a certificate of conformance because there is no radiation assurance testing and they are not
DLA qualified devices.
4. Evaluation board uses the /PROTO parts. The /PROTO parts are not rated or certified for Total Ionizing Dose (TID) or Single Event Effect (SEE)
immunity.
FN4471 Rev.3.00
Sep 21, 2018
Page 2 of 6







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)