Operational Amplifier. HS1-5104ARH Datasheet
July 1999 File Number 4606.1
Radiation Hardened Low Noise Quad
Intersil‘s Satellite Applications FlowTM (SAF) devices are
fully tested and guaranteed to 100kRAD total dose. These
QML Class T devices are processed to a standard ﬂow
intended to meet the cost and shorter lead-time needs of
large volume satellite manufacturers, while maintaining a
high level of reliability.
The HS-5104ARH-T is a radiation hardened, monolithic
quad operational ampliﬁer that provides highly reliable
performance in harsh radiation environments. Its excellent
noise characteristics coupled with a unique array of dynamic
speciﬁcations make this ampliﬁer well-suited for a variety of
satellite system applications. Dielectrically isolated, bipolar
processing makes this device immune to Single Event
The HS-5104ARH-T shows almost no change in offset
voltage after exposure to 100K RAD(Si) gamma radiation,
with only a minor increase in current. Complementing these
speciﬁcations is a post radiation open loop gain in excess of
This quad operational ampliﬁer is available in an industry
standard pinout, allowing for immediate interchangeability
with most other quad operational ampliﬁers.
Speciﬁcations for Rad Hard QML devices are controlled by
the Defense Supply Center in Columbus (DSCC). The SMD
numbers listed below must be used when ordering.
Detailed Electrical Speciﬁcations for the HS-5104ARH-T
are contained in SMD 5962-95690. A “hot-link” is provided
from our website for downloading.
Intersil‘s Quality Management Plan (QM Plan), listing all
Class T screening operations, is also available on our
-55 to 125
-55 to 125
-55 to 125
-55 to 125
NOTE: Minimum order quantity for -T is 150 units through
distribution, or 450 units direct.
• QML Class T, Per MIL-PRF-38535
• Radiation Performance
- Gamma Dose (γ) 1 x 105 RAD(Si)
- No Latch-Up, Dielectrically Isolated Device Islands
• Low Noise
- At 1kHz . . . . . . . . . . . . . . . . . . . . . . . . 4.3nV/√Hz (Typ)
- At 1kHz . . . . . . . . . . . . . . . . . . . . . . . . 0.6pA/√Hz (Typ)
• Low Offset Voltage . . . . . . . . . . . . . . . . . . . . 3.0mV (Max)
• High Slew Rate . . . . . . . . . . . . . . . . . . . . . . 2.0V/µs (Typ)
• Gain Bandwidth Product . . . . . . . . . . . . . . . 8.0MHz (Typ)
HS1-5104ARH-T (SBDIP), CDIP2-T14
OUT 1 1
OUT 2 7
14 OUT 4
8 OUT 3
HS9-5104ARH-T (FLATPACK), CDFP3-F14
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation.
(2420µm x 2530µm x 483µm ±25.4µm)
95 x 99 x 19mils ±1mil
Type: Al Si Cu
Thickness: 16.0kÅ ±2kÅ
Metallization Mask Layout
Type: Nitride (Si3N4) over Silox (SiO2)
Nitride Thickness: 3.5kÅ ±1.5kÅ
Silox Thickness: 12.0kÅ ±2kÅ
WORST CASE CURRENT DENSITY:
< 2.0e5 A/cm2
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certiﬁcation.
Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time with-
out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com