DatasheetsPDF.com

DC/DC COnverters. D221I Datasheet

DatasheetsPDF.com

DC/DC COnverters. D221I Datasheet






D221I COnverters. Datasheet pdf. Equivalent




D221I COnverters. Datasheet pdf. Equivalent





Part

D221I

Description

D200I Series / High Isolation Miniature / 2W SIP DC/DC COnverters



Feature


D200I Series High Isolation Miniature, 2 W SIP DC/DC Converters Electrical Speci fications Specifications typical @ +2 5°C, nominal input voltage & rated out put current, unless otherwise noted. Sp ecifications subject to change without notice. Input Key Features: Paramet er Conditions Min. Typ. Max. 5.5 13 .2 26.4 52.0 0.3 Units ● 2W Output Power ● 3,000 VDC Isolation.
Manufacture

MicroPower Direct

Datasheet
Download D221I Datasheet


MicroPower Direct D221I

D221I; Input Voltage Range ● Miniature SIP C ase ● Single & Dual Outputs Input Fil ter ● >2 MHour MTBF Reverse Polarity Input Current Output ● 28 Standard Mo dels ● Industry Standard Pin-Out Para meter Output Voltage Accuracy Output Vo ltage Balance Line Regulation Load Regu lation (Note 1) Ripple & Noise (20 MHz) (Note 2) Output Power Protection Tempe rature Coefficient Output Sho.


MicroPower Direct D221I

rt Circuit 5 VDC Input 4.5 5.0 12 VDC I nput 10.8 12.0 24 VDC Input 21.6 24.0 4 8 VDC Input 42.0 48.0 Internal Capacito r VDC A Units % % % mV P - P % %/ºC Conditions Min. Typ. ±1.0 Max. ±3 .0 ±1.0 Dual Output , Balanced Loads For Vin Change of 1% ±1.2 See Model Se lection Guide 120 75 ±0.02 Momentary (0.5 Sec.) Conditions 60 Seconds 500 VD C 100 kHz, 1V Min. 3,000.


MicroPower Direct D221I

1,000 60 125 Min. Ambient Case -40 Typ. +25 Max. +85 +100 +125 95 Typ. Max. G eneral Parameter Isolation Voltage Isol ation Resistance Isolation Capacitance Switching Frequency Units VDC MΩ pF kH z Units ºC ºC ºC % Environmental Pa rameter Operating Temperature Range Ope rating Temperature Range Storage Temper ature Range Cooling Humidity Conditions -40 Free Air Convect.

Part

D221I

Description

D200I Series / High Isolation Miniature / 2W SIP DC/DC COnverters



Feature


D200I Series High Isolation Miniature, 2 W SIP DC/DC Converters Electrical Speci fications Specifications typical @ +2 5°C, nominal input voltage & rated out put current, unless otherwise noted. Sp ecifications subject to change without notice. Input Key Features: Paramet er Conditions Min. Typ. Max. 5.5 13 .2 26.4 52.0 0.3 Units ● 2W Output Power ● 3,000 VDC Isolation.
Manufacture

MicroPower Direct

Datasheet
Download D221I Datasheet




 D221I
D200I Series
High Isolation
Miniature, 2W SIP
DC/DC Converters
Key Features:
2W Output Power
3,000 VDC Isolation
Miniature SIP Case
Single & Dual Outputs
>2 MHour MTBF
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min. Typ. Max. Units
5 VDC Input 4.5 5.0 5.5
Input Voltage Range
12 VDC Input 10.8 12.0 13.2
24 VDC Input 21.6 24.0 26.4
VDC
48 VDC Input 42.0 48.0 52.0
Input Filter
Internal Capacitor
Reverse Polarity Input Current
0.3 A
28 Standard Models
Output
Industry Standard Pin-Out Parameter
Output Voltage Accuracy
Conditions
Min. Typ. Max.
±1.0 ±3.0
Units
%
Output Voltage Balance
Dual Output , Balanced Loads
±1.0 %
Line Regulation
For Vin Change of 1%
±1.2
%
Load Regulation (Note 1)
See Model Selection Guide
Ripple & Noise (20 MHz) (Note 2)
75 mV P - P
Output Power Protection
120 %
Temperature Coefficient
±0.02 %/ºC
Output Short Circuit
Momentary (0.5 Sec.)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 3,000
VDC
Isolation Resistance
500 VDC 1,000
Isolation Capacitance
100 kHz, 1V
60
pF
Switching Frequency
125 kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +85
ºC
Operating Temperature Range
Case
+100
ºC
Storage Temperature Range
-40
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95 %
Physical
MicroPower Direct
232 Tosca Drive
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Case Size (5V, 12V & 24V Input Models)
Case Size (48V Input Models)
Case Material
Weight
Reliability Specifications
Parameter
MTBF
Absolute Maximum Ratings
0.76 x 0.24 x 0.37 Inches (19.5 x 6.0 x 9.5 mm)
0.76 x 0.28 x 0.37 Inches (19.5 x 7.2 x 9.5 mm)
Non-Conductive Black Plastic (UL94-V0)
0.09 Oz (2.7g)
Conditions
Min. Typ. Max.
MIL HDBK 217F, 25ºC, Gnd Benign 2.0
Units
MHours
Parameter
Conditions
Min. Typ. Max. Units
5 VDC Input -0.7
9.0
Input Voltage Surge (1 Sec)
12 VDC Input -0.7
24 VDC Input -0.7
18.0
VDC
30.0
48 VDC Input -0.7
55.0
Lead Temperature
1.5 mm From Case For 10 Sec
260 ºC
Internal Power Dissipation
All Models
650 mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.




 D221I
Model Selection Guide
Model
Number
D201I
D202I
D203I
D204I
D205I
D206I
D207I
D211I
D212I
D213I
D214I
D215I
D216I
D217I
D221I
D222I
D223I
D224I
D225I
D226I
D227I
D231I
D232I
D233I
D234I
D235I
D236I
D237I
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
5
4.5 - 5.5
533
35
5
4.5 - 5.5
513
35
5
4.5 - 5.5
495
35
5
4.5 - 5.5
499
35
5
4.5 - 5.5
533
35
5
4.5 - 5.5
504
35
5
4.5 - 5.5
501
35
12 10.8 - 13.2 204
25
12 10.8 - 13.2 212
25
12 10.8 - 13.2 196
25
12 10.8 - 13.2 200
25
12 10.8 - 13.2 216
25
12 10.8 - 13.2 201
25
12 10.8 - 13.2 200
25
24 21.6 - 26.4 92
10
24 21.6 - 26.4 108
10
24 21.6 - 26.4 101
10
24 21.6 - 26.4 101
10
24 21.6 - 26.4 108
10
24 21.6 - 26.4 102
10
24 21.6 - 26.4 99
10
48 42.0 - 52.0 59
10
48 42.0 - 52.0 54
10
48 42.0 - 52.0 51
10
48 42.0 - 52.0 50
10
48 42.0 - 52.0 54
10
48 42.0 - 52.0 51
10
48 42.0 - 52.0 50
10
Voltage
(VDC)
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
Output
Current
(mA, Max)
400.0
400.0
165.0
133.0
±200.0
±83.0
±66.0
400.0
400.0
165.0
133.0
±200.0
±83.0
±66.0
400.0
400.0
165.0
133.0
±200.0
±83.0
±66.0
400.0
400.0
165.0
133.0
±200.0
±83.0
±66.0
Current
(mA, Min)
10.0
8.0
3.0
2.5
±4.0
±1.5
±1.0
10.0
8.0
3.0
2.5
±4.0
±1.5
±1.0
10.0
8.0
3.0
2.5
±4.0
±1.5
±1.0
10.0
8.0
3.0
2.5
±4.0
±1.5
±1.0
Load
Regulation
(%, Max)
12
12
8
8
12
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
Efficiency
(%, Typ)
Fuse Rating
Slow-Blow
(mA)
75 1,000
78 1,000
80 1,000
80 1,000
75 1,000
79 1,000
79 1,000
67 500
78 500
85 500
83 500
77 500
82 500
82 500
74 200
77 200
81 200
82 200
77 200
81 200
84 200
70 100
77 100
81 100
82 100
76 100
81 100
82 100
Notes:
1. Output load regulation is specified for a load change of 20% to 100%.
2. When measuring output ripple, it is recommended that an external ceramic capacitor (approx 10 µF)
be placed from the +Vout pin to the -Vout pin for single output units and from each output to common
for dual output units.
3. All 3.3, 5 and ±5 VDC output models may be operated to +85ºC ambient with an unobstructed airflow
of 3.6 ft/S (1.1 m/S).
4. The 5V, 12V and 24V input units do not require external components to operate, but the use of an
input capacitor (10 µF) may enhance performance in some applications. An output capacitor (1.0 µF
to 10 µF) may be used to reduce ripple. The 48V input models require an input capacitor of 4.7 uF to
47 uF (dependent upon the application).
5. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the
load across the positive (+Vout) and negative (-Vout) outputs and float the output common.
6. It is recommended that a fuse be used on the input of a power supply for protection. See the table above
for the correct rating.
Pin Connections
Pin Single
Dual
1 +Vin +Vin
2 -Vin -Vin
5 -Vout -Vout
6 No Pin Common
7 +Vout +Vout
Mechanical Dimensions
Derating Curve
Capacitive
Load
Single Output
(μF Max)
470
Dual Output
(μF Max)
±390
Notes: All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.01 (±0.25)
Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
TEL: (781) 344-8226 FAX: (781) 344-8481
E-Mail: sales@micropowerdirect.com







Recommended third-party D221I Datasheet






@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)