CE2000 Amplifier Datasheet

CE2000 Datasheet PDF, Equivalent


Part Number

CE2000

Description

Amplifier

Manufacture

Crown

Total Page 2 Pages
PDF Download
Download CE2000 Datasheet PDF


CE2000
www.DataSheet4U.com
CE 2000
CE-SERIES
T he CE-Series of Crown amplifiers
are professional tools designed and
built for professional use. Engineered
and manufactured by the same teams who
built Crown’s acclaimed Macro-Tech® and K-
Series amps, the CE 2000 has the rugged
heart and soul that have characterized
Crown’s amplifiers for over 30 years.
With many of the same controls and features
you’ve come to expect from Crown, CE-
Series amplifiers feature front-panel detented
level controls, useful function indicators,
proportional fan-assisted cooling, short-
circuit protection and more.
For superior flexibility, Crown CE-Series
amplfiers can work with a range of Crown
SST (System Solution Topologies) modules
which provide true professional features like
fixed-point crossover and summed bass
output.
With a powerful, reliable performance, CE-
Series amps easily handle real 2-ohm loads
and are capable of chest-thumping lows.
Plus, your investment in an CE-Series ampli-
fier is backed by Crown’s unequaled Three-
Year, No-Fault, Fully Transferable Warranty
that covers everything.
For more details about the Crown CE-Series,
contact the Crown Technical Support Group
at 800-342-6939 or 219-294-8200. Also,
visit the Crown Audio website at
www.crownaudio.com.
Specifications
Note: All measurements relate to 120-volt, 60-Hz units in
Stereo mode with 8-ohm loads and an input sensitivity of 26-
dB gain at 1-kHz rated power unless otherwise specified.
Specifications for units supplied outside the U.S.A. may vary
slightly at different AC voltages and frequencies.
Power
Output Power:
Features
• Accurate, uncolored sound with very low dis-
tortion for the best in music and voice repro-
duction.
• Bridge-mono/stereo mode switch allows you
to set up your amps/speakers in the configu-
ration that best suits your needs.
• Advanced protection circuitry guards against:
shorted outputs, open circuits, DC, mis-
matched loads, general overheating, high-
frequency overloads and internal faults.
• Extremely versatile, handling a wide range
of speaker impedances and outputs.
• Switchable input sensitivity.
• Proportional speed fan optimizes cooling effi-
ciency.
• Shallow rack depth. Only 12.25 inches deep!
• Choice of Speakon®, binding post, or barrier
strip outputs (Speakon® comes standard).
• Choice of balanced 1/4-inch (6.35-mm), XLR,
or barrier strip inputs.
• The best Three-Year, No-Fault, Fully Transfer-
able Warranty in the business! It even covers
round-trip ground shipping in the U.S. for all
warranty work.
Load Impedance: Safe with all types of
loads. Rated for 2, 4 and 8 ohms in Stereo
mode, 4 and 8 ohms in Bridge-Mono mode.
Voltage Gain to 1-kHz, 8-ohm rated output:
32.1-dB gain at 1.4-volt sensitivity;
26-dB gain at 2.83-volt sensitivity.
Required AC Mains: 50/60 Hz (North Ameri-
can units are 60 Hz only); 100-, 120- and
230-/240-VAC (±10%) units are available.
AC Line Current,
100 Volts: 11.4 A;
120 Volts: 9.5 A;
230-240 Volts: 5.0 A;
At Idle: All amps draw no more than 90
watts.
AC Line Connector: NEMA 5-15P (15 A).
Performance
Frequency Response: ±0.2 dB from 20 Hz to
25 kHz at 1 watt.
Phase Response: ±15 degrees from 20 Hz to
20 kHz at 1 watt.
Signal to Noise Ratio,
A-Weighted:
Better than 105 dB below rated 1-kHz
power;
20 Hz to 20 kHz:
Better than 100 dB below rated 1-kHz
power.
Total Harmonic Distortion (THD): 0.5% or
less true THD from 20 Hz to 20 kHz.
Intermodulation Distortion (IMD): (60 Hz
and 7 kHz at 4:1) Less than 0.1% at rated
power to 35 dB below rated power at 8 ohms.
Damping Factor: Better than 400 from 10 Hz
to 400 Hz.
Crosstalk: Better than 55 dB below rated
power, 20 Hz to 20 kHz.
Common Mode Rejection (CMR): Greater
than 70 dB from 20 Hz to 1 kHz.
DC Output Offset (Shorted Input): ±10 mV.
Controls and Connectors
Level: A detented rotary level control for each
channel located on the front panel.
Power: An on/off rocker switch located on the
front panel.
Mode: A two-position switch located on the
back panel below the input connectors which,
when turned to stereo, operates the amplifier
as two independent channels. When “Bridge-
Mono” mode is selected, the amplifier bridges
the two output channels for twice the output
voltage.
Reset: A front-panel push button used to
reset the circuit breaker that protects the
power supply.
Sensitivity: A two-position switch located on
the back panel next to the Mode switch.
Switchable between 1.4 volts for full output
into an 8-ohm load (default setting), or a fixed
voltage gain of 26 dB. 0.775-volt sensitivity
available as a Service Option.
Fault Jack: A back-panel RJ-11 jack that may
be remotely monitored to signal amplifier
Fault condition. An LED or other signalling
device (not supplied) may be used.
Indicators
(all located on front panel)
Signal: A green LED for each channel which
flashes when a very low-level signal (>–40
dBm) is present at input. May be used for
troubleshooting cable runs.
Clip: A red LED for each channel which turns
on when distortion becomes audible in the
amplifier output.

CE2000
www.DataSheet4U.com
CE 2000
Fault: Normally off, this red indicator will
blink under five different conditions:
1. When the amplifier is first powered up, until the
unit is ready for operation.
2. If the heatsinks reach a temperature above nor-
mal working limits.
3. If the transformer thermal protection circuit is ac-
tivated.
4. If amplifier output wires develop a short-circuit.
5. Should the amplifier output stage become non-
operational.
This circuit may be monitored remotely by
plugging a simple switching circuit using an
LED or other signaling device into the back-
panel RJ-11 (Fault) jack. Under some condi-
tions, the output of the amplifier will be
muted.
Power: A green LED that turns on when the
amplifier has been turned on and has power.
Input/Output
Input Connector (standard module): One
Neutrik® Combo connector for each channel
which features a balanced ¼-inch (6.35-mm)
phone jack and a 3-pin female XLR connector,
in parallel with a barrier strip termination.
Input Stage: Input is electronically balanced
and employs precision 1% resistors.
Input Impedance: Nominally 20 k ohms,
balanced. Nominally 10 k ohms, unbalanced.
Input Sensitivity: 1.4 volts for standard 1-kHz
power, or fixed 26-dB gain. 0.775-volt sensi-
tivity available as a Service Option.
Output Connectors: Two Neutrik® Speakon®
NL4MP (mates with NL4FC) output connec-
tors. Optional 5-way binding post or barrier
strip outputs (in parallel with Speakon®
connectors) are available.
DC Output Offset: ±10 millivolts.
Output Signal,
Stereo: Unbalanced, two-channel;
Bridge-Mono: Balanced, single-channel.
Channel 1 controls are active; Channel 2
should be turned down.
Wiring Configuration:
OUTUT PIN ASSIGNMENT
PIN CH
PIN CH
1+ 2
1+ 1
12
11
2+ 2+ 2
2 22
CH-2
CH-1
Protection
CE-Series amplifiers are protected against
shorted, open or mismatched loads; over-
loaded power supplies; excessive tempera-
ture; chain destruction phenomena; input
overload damage; and high-frequency blow-
ups. They also protect loudspeakers from
input/output DC, large or dangerous DC
offsets and turn-on/turn-off transients.
Options
Accessories: CE-HANDLES—handle kit; SST-
SBSC—variable Linkwitz-Riley stereo cross-
over with mono-summed sub-bass outputs;
SST-MX—100-Hz Linkwitz-Riley crossover
with stereo sub-bass output; SST-SX—80-/
120-Hz switchable Linkwitz-Riley crossover
with mono summed sub-bass output; CE-
AS1—barrier block alternate output connec-
tors;* CEAS2—5-way binding post alternate
output connectors.* SST-4622, SST-3632,
SST-4632—custom two-channel crossover
networks with equalization and delay pur-
posely engineered for use with JBL model
4622, 3632 and 4632 cinema speakers. SST-
SBSC 3632T, SST-SBSC 4632T—custom
three-channel crossover networks with CD-
horn equalization and mono-summed low-
frequency outputs similarly designed for use
with JBL model 3632T and 4632T cinema
speakers.
Construction
Rugged steel chassis is formed into a durable
package any stagehand could love. Coated
with environmentally friendly powder for long
life and ease of maintenance.
Cooling: Proportional speed fan.
Dimensions: EIA Standard 19-inch rack
mount width (EIA RS-310-B), 5.25-inch
(13.34-cm) height and 12.25-inch (31.11-cm)
depth behind front mounting surface.
Weight: The CE 2000 weighs 40.3 pounds
(18.28 kg). For shipping weight, add 6
pounds (2.7 kg).
*Compatible with CE versions CE 1000A and CE 2000A
amplifiers (current release).
Crown’s Three-Year, No-Fault, Fully Transferable Warranty
Crown offers a Three-Year, No-Fault, Fully Transferable Warranty for every new Crown ampli-
fier—an unsurpassed industry standard. With this unprecedented No-Fault protection, your
new Crown amplifier is warranted to meet or exceed original specifications for the first three
years of ownership. During this time, if your amplifier fails, or does not perform to original
specifications, it will be repaired or replaced at our expense. About the only things not cov-
ered by this warranty are those losses normally covered by insurance and those caused by
intentional abuse. And the coverage is transferable, should you sell your amplifier.
See your authorized Crown dealer for full warranty disclosure and details. For customers
outside of the USA, please contact your authorized Crown distributor for warranty information
or call 219-294-8200.
Crown International
P.O. Box 1000
Elkhart, IN 46515-1000
TEL: 219-294-8200
FAX: 219-294-8FAX
www.crownaudio.com
Specifications subject to change without prior notice.
Crown and Macro-Tech are registered trademarks of Crown
International. Other trademarks are the property of their
respective owners. Printed in U.S.A.
©2001 Crown Audio, Inc.
08/01
128391-2


Features www.DataSheet4U.com C E - S E R I E S CE 2000 he CE-Series of Crown amplifier s are professional tools designed and b uilt for professional use. Engineered a nd manufactured by the same teams who b uilt Crown’s acclaimed Macro-Tech® a nd KSeries amps, the CE 2000 has the ru gged heart and soul that have character ized Crown’s amplifiers for over 30 y ears. With many of the same controls an d features you’ve come to expect from Crown, CESeries amplifiers feature fro nt-panel detented level controls, usefu l function indicators, proportional fan -assisted cooling, shortcircuit protect ion and more. For superior flexibility, Crown CE-Series amplfiers can work wit h a range of Crown SST (System Solution Topologies) modules which provide true professional features like fixed-point crossover and summed bass output. With a powerful, reliable performance, CESe ries amps easily handle real 2-ohm load s and are capable of chest-thumping low s. Plus, your investment in an CE-Series amplifier is backed by Crown’.
Keywords CE2000, datasheet, pdf, Crown, Amplifier, E2000, 2000, 000, CE200, CE20, CE2, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)