HI8282 DUAL RECEIVER Datasheet

HI8282 Datasheet, PDF, Equivalent


Part Number

HI8282

Description

ARINC 429 SERIAL TRANSMITTER AND DUAL RECEIVER

Manufacture

Holt Integrated Circuits

Total Page 14 Pages
Datasheet
Download HI8282 Datasheet


HI8282
hSa t aD.www
January 2001
HI-8282
GENERAL DESCRIPTION
The HI-8282 is a silicon gate CMOS device for interfacing
the ARINC 429 serial data bus to a 16-bit parallel data bus.
Two receivers and an independent transmitter are
provided. The receiver input circuitry and logic are
designed to meet the ARINC 429 specifications for loading,
level detection, timing, and protocol. The transmitter
section provides the ARINC 429 communication protocol.
Additional interface circuitry such as the Holt HI-8382 is
required to translate the 5 volt logic outputs to ARINC 429
drive levels.
The 16-bit parallel data bus exchanges the 32-bit ARINC
data word in two steps when either loading the transmitter
or interrogating the receivers. The data bus interfaces with
CMOS and TTL.
Timing of all the circuitry begins with the master clock input,
CLK. For ARINC 429 applications, the master clock
frequency is 1 MHz.
Each independent receiver monitors the data stream with a
sampling rate 10 times the data rate. The sampling rate is
software selectable at either 1MHz or 125KHz. The results
of a parity check are available as the 32nd ARINC bit. The
HI-8282 examines the null and data timings and will reject
erroneous patterns. For example, with a 125 KHz clock
selection, the data frequency must be between 10.4 KHz
and 15.6 KHz.
The transmitter has a First In, First Out (FIFO) memory to
store 8 ARINC words for transmission. The data rate of the
transmitter is software selectable by dividing the master
clock, CLK, by either 10 or 80. The master clock is used to
set the timing of the ARINC transmission within the required
resolution.
APPLICATIONS
! Avionics data communication
! Serial to parallel conversion
! Parallel to serial conversion
FEATURES
! ARINC specification 429 compatible
! 16-Bit parallel data bus
! Direct receiver interface to ARINC bus
! Timing control 10 times the data rate
! Selectable data clocks
! Receiver error rejection per ARINC
specification 429
! Automatic transmitter data timing
! Self test mode
! Parity functions
! Low power, single 5 volt supply
! Industrial & full military temperature ranges
! DESC SMD part number
PIN CONFIGURATION (Top View)
N/C - 1
D/R1 - 2
D/R2 - 3
SEL - 4
EN1 - 5
EN2 - 6
BD15 - 7
BD14 - 8
BD13 - 9
BD12 - 10
BD11 - 11
HI-8282PQI
&
HI-8282PQT
33 - N/C
32 - N/C
31 - CWSTRX
30 - ENTX
29 - 429DO
28 - 429DO
27 - TX/R
26 - PL2
25 - PL1
24 - BD00
23 - BD01
44-Pin Plastic Quad Flat Pack (PQFP)
(See page 4-38 for additional Package Pin Configurations)
(DS8282 Rev. A)
HOLT INTEGRATED CIRCUITS
4-29
01/01

HI8282
mocU.4teehSatDaw.
PIN DESCRIPTION
HI-8282
SYMBOL
VCC
429DI1 (A)
429DI1 (B)
429DI2 (A)
429DI2 (B)
D/R1
D/R2
SEL
EN1
EN2
BD15
BD14
BD13
BD12
BD11
BD10
BD09
BD08
BD07
BD06
GND
BD05
BD04
BD03
BD02
BD01
BD00
PL1
PL2
TX/R
FUNCTION
POWER
INPUT
INPUT
INPUT
INPUT
OUTPUT
OUTPUT
INPUT
INPUT
INPUT
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
POWER
I/O
I/O
I/O
I/O
I/O
I/O
INPUT
INPUT
OUTPUT
429DO
429DO
ENTX
CWSTR
CLK
TX CLK
MR
OUTPUT
OUTPUT
INPUT
INPUT
INPUT
OUTPUT
INPUT
DESCRIPTION
+5V ±5%
ARINC receiver 1 positive input
ARINC receiver 1 negative input
ARINC receiver 2 positive input
ARINC receiver 2 negative input
Receiver 1 data ready flag
Receiver 2 data ready flag
Receiver data byte selection (0 = BYTE 1) (1 = BYTE 2)
Data Bus control, enables receiver 1 data to outputs
Data Bus control, enables receiver 2 data to outputs if EN1 is high
Data Bus
Data Bus
Data Bus
Data Bus
Data Bus
Data Bus
Data Bus
Data Bus
Data Bus
Data Bus
0V
Data Bus
Data Bus
Data Bus
Data Bus
Data Bus
Data Bus
Latch enable for byte 1 entered from data bus to transmitter FIFO.
Latch enable for byte 2 entered from data bus to transmitter FIFO. Must follow PL1.
Transmitter ready flag. Goes low when ARINC word loaded into FIFO. Goes high
after transmission and FIFO empty.
"ONES" data output from transmitter.
"ZEROES" data output from transmitter.
Enable Transmission
Clock for control word register
Master Clock input
Transmitter Clock equal to Master Clock (CLK), divided by either 10 or 80.
Master Reset, active low
HOLT INTEGRATED CIRCUITS
4-30


Features h S ata D.w w w HI-8282 January 2001 G ENERAL DESCRIPTION The HI-8282 is a sil icon gate CMOS device for interfacing t he ARINC 429 serial data bus to a 16-bi t parallel data bus. Two receivers and an independent transmitter are provided . The receiver input circuitry and logi c are designed to meet the ARINC 429 sp ecifications for loading, level detecti on, timing, and protocol. The transmitt er section provides the ARINC 429 commu nication protocol. Additional interface circuitry such as the Holt HI-8382 is required to translate the 5 volt logic outputs to ARINC 429 drive levels. The 16-bit parallel data bus exchanges the 32-bit ARINC data word in two steps whe n either loading the transmitter or int errogating the receivers. The data bus interfaces with CMOS and TTL. Timing of all the circuitry begins with the mast er clock input, CLK. For ARINC 429 appl ications, the master clock frequency is 1 MHz. Each independent receiver monit ors the data stream with a sampling rate 10 times the data rate.
Keywords HI8282, datasheet, pdf, Holt Integrated Circuits, ARINC, 429, SERIAL, TRANSMITTER, AND, DUAL, RECEIVER, I8282, 8282, 282, HI828, HI82, HI8, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)