Performance Switchers. GPFM115 Datasheet

GPFM115 Switchers. Datasheet pdf. Equivalent

Part GPFM115
Description 115 Watt Global Performance Switchers
Feature 115 Watt Global Performance Switchers GLOBAL PERFORMANCE SWITCHERS FEATURES: • 115 Watts of continuo.
Manufacture SL Power Electronics
Total Page 2 Pages
Datasheet
Download GPFM115 Datasheet



GPFM115
GLOBAL PERFORMANCE SWITCHERS
FEATURES:
• 115 Watts of continuous power with forced air
• Power factor corrected
w•• w7Swm4.-Da8alt1alS%pheaeetc4fkUfia.ncgeiteen3c.y3” x 5.25” x 1.5” inches
• Power fail warning, remote sense
• Optional cover with cooling fan
• Medical Approval to UL2601-1, CSA-C22.2
No. 601.1, EN60601-1
• RoHS Compliant Model Available (G suffix)
GPFM115 Medical
115 Watt Global Performance Switchers
DC Power Supplies
SPECIFICATIONS
Ac Input
85-264 Vac, 47-63 Hz single phase
Output Power
Continuous rating is 80 W with unrestricted natural convection, or 115 W with
forced convection. All models capable of 110% of rated power for 60 sec.,
10% duty cycle maximum.
Input Current
Maximum input current at 90 Vac, 60 Hz with full rated load is 1.7 A. Input
current harmonic content meets the requirements of IEC1000-3-2 for all load
conditions at 230 Vac input. Active input circuitry provides high power factor
of .96 min, .99 typical.
Inrush Current
Inrush 240 Vac is less than 37 A, averaged over thr first ac halfcycle under cold
start conditions. Limiting provided by internal thermistors.
Holdup Time
25 ms minimum from loss of ac input at full load.
Power Fail
TTL / CMOS compatible output goes low (<0.5 V) 8 ms before output voltage
drops more than 4% below nominal voltage upon loss of ac power. The signal is
factory set to trip before there is insufficient power stored in the primary to sus-
tain the output. Signal can sink 1.6 mA or source 400 μA at 2.7 V (Fan-out = 1).
Efficiency
74 to 81% depending upon model
DC Output Specification
Total regulation is the maximum deviation from the nominal voltage for all
steady state loading conditions. Peak ratings are for 60 s maximum duration,
10% duty cycle. Consult factory for application assistance.
Remote Sense
Provided as a standard feature on all models. Capable of compensating for
0.25 V total of cabling losses.
Overload Protection
Fully protected against short circuit and output overload. Short circuit protec-
tion is cycling type power limit. Recovery after fault is automatic. Consult
factory for specific condition limits.
Overvoltage Protection
Built in on all models - See voltage and current chart for individual model
output limits. When OVP fires, the output converter stops providing input
power to output. Output voltage decay is dependent upon loading.
Output Noise
0.5% rms, 1% pk-pk, 20 MHz Bandwidth, differential mode. Measured with
noise probe directly across output terminals of the power supply.
Transient Response
Main Output 500 μs typical response time for return to within 0.5% of final value
for a 50% load step change, ∆i/∆t<0.2 A/μs. Maximum voltage deviation is 3.5%.
Minimum Load
No minimum load required to maintain output specifications. An abrupt change in
output current from > 90% to < 2% load may cause a false triggering of the power
fail signal.
Voltage Adjustment
Main output ±5%.
Temperature Coefficient
0.03%/°C typical on all outputs.
Thermal Shutdown
Provided as a standard feature. Designed to protect unit from prolonged over
temperature.
Fan Output
An additional 12 Vdc (nominal 10.5 V), 100 mA output suitable for powering a dc
fan is included in all models. The fan output is referenced to +out. Due to high
pk-pk noise and low regulation, it is not recommended that this output be used
for any other purpose.
Input Protection
Internal ac fuse provided on all models. Fuse does not blow on overload or short
circuit -- fuse blows only if a catastrophic failure occurs in the unit.
EMI/EMC Compliance
All models include built-in EMI filtering to meet the following emissions require-
ments:
EMI SPECIFICATIONS
COMPLIANCE LEVEL
Conducted Emissions
Static Discharge
RF Field Susceptibility
Fast Transients/Bursts
Surge Susceptibility
Line Frequency Harmonics
Conducted RF Susceptibility
Voltage Dips and Interruptions
EN55011 Class B; FCC Class B
EN61000-4-2, 6 kV contact, 8 kV air
EN61000-4-3, 3 V/meter
EN61000-4-4, 2 kV, 5 kHz
EN61000-4-5, 1 kV diff., 2 kV com.
EN61000-3-2 Class A
EN61000-4-6, 3 V
EN61000-4-11, Consult factory for more
details.
Leakage Current
90 μA normal conditions (132 Vac @ 60 Hz input) or 250 μA (264 Vac) single fault.
Medical Safety
All models are Certified to be in compliance with the applicable requirements of
UL 2601, CSA 22.2 No. 601.1-M90, IEC 601-1 (1988), EN 60601-1: 1990. (Consult
factory for approval status)
All specifications are typical at nominal input, full load at 25OC unless otherwise stated



GPFM115
Medical
Model
GPFM115-5
GPFM115-12
GPFM115-13
GPFM115-15
GPFM115-24
GPFM115-28
GPFM115-48
RoHS
Suffix*
G
G
G
G
G
G
G
Voltage
Output
5.1 V
12 V
13 V
15 V
24 V
28 V
48 V
Output Ad-
justment
±5%
±5%
±5%
±5%
±5%
±5%
±5%
Output
Maximum (A)
12 A
6.7 A
6.2 A
5.3 A
3.3 A
2.9 A
1.7 A
Maximum (B)
20 A
9.6 A
8.8 A
7.7 A
4.8 A
4.1 A
2.4 A
Output Peak
25 A
10.8 A
9.9 A
8.7 A
5.4 A
4.6 A
2.7A
Total
Regulation
2%
2%
2%
2%
2%
2%
2%
OVP
Setpoint
6.2 ± 0.6 V
14 ± 1.1 V
15 ± 1.1 V
18.5 ± 1.5 V
28 ± 2.5 V
34 ± 2.8 V
55 ± 4.0 V
Notes:
* Add “G” suffix to part number for RoHS compliant model.
A. Maximum continuous current rating for unrestricted convection cooling.
B. Maximum continuous current rating with 150 LFM air or cover option.
C. Add “-C” after voltage in model number for cover with fan option.
Ripple/
Noise
1%
1%
1%
1%
1%
1%
1%
Notes
C
C
C
C
C
C
C
GPFM115 MECHANICAL SPECIFICATIONS
JI INPUT: (AMP P.C.B. HEADER P.N 640445-5)
PIN 1) AC LINE
PIN 2) = N/C
PIN 3) = AC NEUTRAL
PIN 4) = N/C
PIN 5) = AC GROUND
SIGNALS: J2
AMP P.C.B. HEADER P/N 640456-4
MATING CONNECTOR P/N 640621-4
PIN 1) POWER FAIL
PIN 2) -SENSE
PIN 3) +SENSE
PIN 4) COMMON
FAN: J4
AMP P.C.B. HEADER P/N 640456-2
MATING CONNECTOR P/N 640621-2
PIN 1) -
PIN 2) +
OUTPUT
J3- 5A MAXIMUM CONTINUOUS CURRENT PER
CONNECTOR PIN.
AMP P.C.B. HEADER P/N 640445-8
PIN 1-4) +Vout
PINS 5-8) RETURN
OUTPUT-MATING CONNECTOR AMP P/N
HOUSING 640250-8
CONTACT 770476-1
INPUT MATING CONNECTOR AMP P/N
HOUSING 640250-5
CONTACT 770476-1
MAX. SCREW PROTRUSION THROUGH CHASSIS = 0.08”
[2 MM], CHASSIS THICKNESS = 0.080” [2 MM]
OPTIONAL COVER/FAN ASSEMBLY
AVAILABLE P/N 09-115CF
ENVIRONMENTAL SPECIFICATIONS
Temperature (A)
Humidity (A)
Shock (B)
Altitude
Vibration (C)
OPERATING
0 to 50°
0 to 95% RH
20 gpk
-500 to 10,000 ft
1.5 g rms’0.003 g2/Hz
NON-OPERATING
-40 to +85°C
0 to 95% RH
40 gpk
-500 to 40,000 ft
5 g rms’0.026 g2/Hz
A. Units should be allowed to warm up/operate under non-condensing
conditions before application of power. Derate output current and total
output power by 2.5% per °C above 50°C. For operation in a confined
space, moving air may be required. Under all conditions, the cooling vs.
load profile should be such that chassis temperatures do not exceed
90°C for extended periods.
B. Shock testing—half-sinusoidal, 10 ± 3 ms duration, ± direction, 3
orthogonal axes, total 6 shocks.
C. Random vibration—10 to 2000Hz, 6dB/octave roll-off from 350 to
2000Hz, 3 orthogonal axes. Tested for 10 min./axis operating and 1
hr./axis non-operating.
SL Power Electronics, Inc. 6050 King Drive, Bldg. A, Ventura, CA, 93003, USA. Phone:(805) 486 4565 Fax:(805) 487 8911 Email: info@slpower.com www.slpower.com Rev.
5/6/08. Data Sheet © 2008 SL Power Electronics, Inc. The information and specifications contained in this data sheet are believed to be correct at time of publication.
However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice.





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)