speed controller. TVSS5 Datasheet

TVSS5 controller. Datasheet pdf. Equivalent

TVSS5 Datasheet
Recommendation TVSS5 Datasheet
Part TVSS5
Description electronic three phase fan speed controller
Feature TVSS5; TVSS5 electronic three phase fan speed controller The TVSS5 automatically controls the speed of t.
Manufacture ETC
Datasheet
Download TVSS5 Datasheet




ETC TVSS5
TVSS5
electronic three phase fan speed controller
The TVSS5 automatically controls the speed of three phase (3 x 400 VAC/50 Hz) voltage
controllable electric motors with a 0-10 VDC or 0-20 mA control signal. This makes it pos-
sible to control these motors automatically with an external PD-controller, remote with
a potentiometer or a microprocessor with analog output. There is also a connection for
a remote start/stop switch. The working principle of this product series is based on the
so-called zero crossing detection. An optotriac combined with a microprocessor ensures
flawless and accurate control.
There are two working modes, internally selectable by switch. With kickstart the motor will
always start or restart at max. speed for 10 seconds, after which it will automatically follow
the position set by the 0-10 VDC or 0-20 mA control signal. Without kickstart the motor
starts according to the position set by the 0-10 VDC or 0-20 mA control signal.
The CNVT-PWM-010V can be connected to provide a conversion of a PWM signal to a 0-10 V signal.
F e a t u r es
ƒƒ Power supply 3 x 400 VAC/50Hz
ƒƒ Infinitely variable control
ƒƒ Min. and max. speed internally adjustable
ƒƒ Off-level selectable by slide switch
ƒƒ Kickstart or soft start selectable by slide switch
ƒƒ 0-10 VDC/0-20 mA selectable by slide switch
ƒƒ LED indication normal operation and alarm status
ƒƒ Maximal ambient temperature: 40 °C
ƒƒ According to the Low Voltage Directive: 2006/95/
EC / the EMC Directive: 2004/108/EC
ƒƒ RS485 Modbus
TVSS5-30-DT
TVSS5-60-DT
TVSS5-30DDT
TVSS5-60DDT
TVSS5-30CDT
TVSS5-60CDT
Current rating Executions
3 A circuit board only
6 A circuit board only
3 A DIN rail mounting (EN 50-022)
6 A DIN rail mounting (EN 50-022)
3 A fingerproof cover included
6 A fingerproof cover included
Wiring diagram
MTP10
External switch
External potentiometer 10 K
0-10 V/0-20 mA
Rs485
SW SW VCC Ai GND A /B 12V
Vmin
Vmax
O -level
Pe
N
RST
TK
SW
Ai
A /B
GND
UVW
VCC
12V
Vmin
Vmax
Off-level
Sw1
Sw2
Sw3
Sw4
power earth
neutral (optional)
3-phase power supply
TK terminal contact from motor
remote start/stop
analog signal (0-10 V/0-20 mA)
RTU Modbus communication
ground
regulated output to three-phase motor
power supply for external potentiometer
12 VDC/1 mA
supply output 12 VDC/100 mA
minimum speed adjustment
maximum speed adjustment
off-level adjustment
input signal selection 0-10 VDC/0-20 mA
kickstart selection on/off
off-level selection on/off
0-10 V, 10-0 V selection
(from hardware version 3.0)
Ope r a t i o n
V out
400
OFF level disabled
260
250
80
V max
V min
0
10
20
Vdc
mA
V
in
V out = ((V in/10)*(V max-V min))+V min
V out
400
260
250
80
OFF level enabled
V max
V min
0 OFF
4
level
10 Vdc
20 mA
V in
V out = (((V in-OFF-level)/(10-OFF-level))*(V max-V min))+V min
07/03/2014
S.3.5.1 241



ETC TVSS5
Modbus registers
Available commands:
ƒƒ Read input registers
Input registers
Data type Description
1 Output 1 current value unsigned int. Current output voltage
2 Vmin [V]
unsigned int. Min. speed voltage
3 Vmax [V]
unsigned int. Max. speed voltage
4 Voff [V]
unsigned int. Off-level voltage
5 …9
10 Alarm TK
11 Alarm phase failed
12 Standby - remote
13 Standby - off-level
14…18
Reserved, returns 0
unsigned int. 0 - normal, 1 - TK
unsigned int. 0 - normal, 1 - Alarm
unsigned int. 0 - normal, 1 - Standby
unsigned int. 0 - normal, 1 - Standby
Reserved, returns 0
Data
Values
0 - 415 300=300 V
80 - 250 100=100 V
260 - 415 330=330 V
10-600
100 = 1 V
600 = 6 V
1 = TK alarm
1 = phase failure alarm
1 = standby/remote
1 = standby/off-level
Available commands:
ƒƒ Read holding register
ƒƒ Write single register
ƒƒ Write multiple registers
Holding registers
1 Modbus address
2 Modbus baud rate
3 Modbus parity mode
4
5
6
7
8…10
11
Device type
HW version
SW version
Modbus enable
Kickstart
12 Remote
13 Off-level
14 0-10 V/10 V-0
15…20
21 Vout [V]
22 Vmin [V]
23 Vmax [V]
24 Voff [V]
25 …40
Data type Description
unsigned int. Device address
unsigned int. Modbus communication baud rate
unsigned int. Parity check mode
unsigned int. Device type: read-only
unsigned int. Hardware version, read-only
unsigned int. Software version, read-only
Reserved, returns 0
unsigned int. Kick start on/off
unsigned int. Remote (BMS) on/off
unsigned int. Off-level on/off
unsigned int. 0-10 V/10 V-0
Reserved, returns 0
unsigned int. Set output voltage
unsigned int. Set min. voltage
unsigned int. Set max. voltage
unsigned int. Set off-level voltage
Reserved, returns 0
Data
1-247
default: 1
1=9600
2=19200
default: 2
0=8N1
1=8E1
2=8O1
default: 1
32= TVSS5
XXX
XXX
0, 1
default: 0
0, 1
0, 1
0, 1
0, 1
0, 80 - 415
0, 80 - 250
0, 260 - 415
0, 10 - 600
Values
100=HW version 1.00
102=SW version 1.02
0 disabled
1 enabled
0 off
1 - on
0 off
1 - on
0- off
1 - on
0 off
1 - on
400=400 VAC, 0 =
according to input
signal Ai
120=120 VAC, 0 =
according to Vmin
trimmer setting
300=300 VAC, 0 =
according to Vmax
trimmer setting
100 = 1 V; 600 =
6 VDC, 0 = according
to off-level trimmer
setting
D i me n s i o n s
D
B
C
A
E
order code
A B C D E net weight gross weight
TVSS5-30-DT 190 100 45 182 98.5 805 g
835 g
TVSS5-60-DT 190 100 45 182 98.5 745 g
775 g
TVSS5-30DDT 195 125 85 - -
885 g
915 g
TVSS5-60DDT 195 125 85 - -
825 g
855 g
TVSS5-30CDT 195 125 100 - -
965 g
990 g
TVSS5-60CDT 195 125 100 - -
905 g
935 g
07/03/2014
S.3.5.1 242







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)