Part Number | ET724 |
Manufacturer | Protek Devices |
Title | STEERING DIODE ARRAY |
Description | www.DataSheet4U.com 05125 ET724 Only One Name Means ProT ek’Tion™ STEERING DIODE ARRA Y APPLICA TIONS ✔ Ethernet - 10/100/1000 Base T ✔ Cellula... |
Features |
C Unless Otherwise Specified
PARAMETER Operating Temperature Storage Temperature Continuous Power Dissipation SYMBOL TJ TSTG PPC VALUE -55°C to 150°C -55°C to 150°C 125 UNITS °C °C mW
ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified
PART NUMBER DEVICE MARKING REPETITIVE PEAK RE...
|
File Size | 195.48KB |
Datasheet |
|
ET720 : www.DataSheet4U.com 05165 ET720 Only One Name Means ProT ek’Tion™ STEERING DIODE ARRA Y APPLICA TIONS ✔ Ethernet - 10/100/1000 Base T ✔ Cellular Phones ✔ Handheld Electronics ✔ FireWire ✔ USB Interface IEC COMPA TIBILITY (EN61000-4) ✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV ✔ 61000-4-4 (EFT): 40A - 5/50ns ✔ 61000-4-5 (Surge): 12A, 8/20µs - Level 1(Line-Gnd) & Level 2(Line-Line) FEA TURES ✔ ESD Protection 40 kilovolts ✔ Provides 14 Lines of Protection ✔ LOW LEAKAGE CURRENT 20nA ✔ ULTRA LOW CAPACITANCE: 3pF Typical MECHANICAL CHARACTERISTICS ✔ Molded JEDEC SO-16 ✔ Weight 0.15 grams (Approximate) ✔ Flammability rating UL 94V-0 ✔ 16mm Tape and Reel Per EIA Standard 481 ✔ Marking: Part .
ET7207 : Etek Microelectronics ET7207 7 CMOS 7 。 7 :63Hz,160Hz,400Hz, 1kHz,2.5kHz,6.25kHz, 16kHz。 7 , 。。 。。。 2.7V 5.5V , 5V。( 1mA),。 Reset Strobe 。 z z z HGND z z 3.3V 5V z 20dB z z z :SOP8(ET7207) z z z Hi-Fi VDDA 1 VSSA 2 OUT 3 STROBE 4 8 C KIN 7 R ESET 6 GND 5 IN Rev 1.0 2007-11-20 1/4 1 2 3 4 5 6 7 8 ET7207 VDD GND OUT STROBE IN HGND RESET CKIN 1/2 VDD Rev 1.0 2007-11-20 2/4 ET7207 Reset Strobe 。 Reset ,。 Reset , 。 Strobe ,63Hz OUT 。 Strobe (63Hz,160Hz,400Hz,1kHz,2.5kHz,6.25kHz,16kHz), 。 Strobe 。 Q VDD IDD IO ZO VOS AV Q FCLK ZIN +6 -60~+150 0~70 1M 2.7 0.5 Vin=100mVpp,fin=1kHz Vin=0.3Vpp,fin=1kHz C=33pF,R=200kohms.
ET7208 : ADC 7:0 adc_one 00h R 63Hz ADC ADC 7:0 adc_two 00h R 160Hz ADC 7:0 adc_three 00h ADC R 400Hz ADC ADC 7:0 adc_four 00h R 1KHz ADC ADC 7:0 adc_five 00h R 2.5KHz ADC ADC 7:0 adc_six 00h R 6.25KHz ADC 7:0 adc_seven 00h ADC R 12KHz ADC 7:0 adc_eight 00h R 7 ADC 2 Addr: 08h Data Set Register Bit Bit Name Default Access 1:0 mdsel 00b R/W Description () 00 01 ADC 10 000 0db 001 6db 010 12db 4:2 gc 000b R/W 011 18db 100 -6db 101 -12db 110 -18db 111 X 6:5 xx xx xx Don’t care 7 shutdown 1b R/W 0 1 :mdsel : (1) 00,;(2) 10,;(3) 01, ADC 。 Rev 1.0 2009-10-14 6/8 ET7208 4 ( 00H) Addr: 0Ah Bit Bit Name .
ET721 : www.DataSheet4U.com 05124 ET721 Only One Name Means ProT ek’Tion™ STEERING DIODE ARRA Y APPLICA TIONS ✔ Ethernet - 10/100/1000 Base T ✔ Set Top Box Interfac ✔ Handheld Electronics ✔ FireWire ✔ USB Interface ✔ Sensor Interface IEC COMPA TIBILITY (EN61000-4) ✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV ✔ 61000-4-4 (EFT): 40A - 5/50ns ✔ 61000-4-5 (Surge): 12A, 8/20µs - Level 1(Line-Gnd) & Level 2(Line-Line) FEA TURES ✔ ESD Protection 40 kilovolts ✔ Low Clamping Voltage ✔ Provides Six (6) Lines of Protection ✔ LOW LEAKAGE CURRENT 200nA ✔ ULTRA LOW CAPACITANCE: 3pF Typical MECHANICAL CHARACTERISTICS ✔ Molded JEDEC SO-8 ✔ Weight 0.1 grams (Approximate) ✔ Flammability rating UL 94V-0 ✔ 12mm .
ET7222 : The ET7222 is 2 to 1port analog switches. Their wide bandwidth and low bittobit skew allow them to pass highspeed differential signals with good signal integrity. Each switch is bidirectional and offers little or no attenuation of the high speed signals at the outputs. Industryleading advantages include a propagation delay of less than 250 ps, resulting from its low channel resistance and low I/O capacitance. Their high channeltochannel crosstalk rejection results in minimal noise interference. Their bandwidth is wide enough to pass HighSpeed USB 2.0 differential signals (480 Mb/s). Features RON is Typically 6.0Ω at VCC = 3.3 V Low BittoBit Skew: Typically 50 ps Low Crosstalk: 4.
ET723 : www.DataSheet4U.com 05174 ET723 Only One Name Means ProT ek’Tion™ STEERING DIODE ARRA Y APPLICA TIONS ✔ Ethernet - 10/100/1000 Base T ✔ Cellular Phones ✔ Handheld Electronics ✔ FireWire ✔ USB Interface IEC COMPA TIBILITY (EN61000-4) ✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV ✔ 61000-4-4 (EFT): 40A - 5/50ns ✔ 61000-4-5 (Surge): 12A, 8/20µs - Level 1(Line-Gnd) & Level 2(Line-Line) FEA TURES ✔ ESD Protection 40 kilovolts ✔ Low Clamping Voltage ✔ Provides Six (6) Lines of Protection ✔ LOW LEAKAGE CURRENT 200nA ✔ ULTRA LOW CAPACITANCE: 5pF Typical MECHANICAL CHARACTERISTICS ✔ Molded JEDEC SO-8 ✔ Weight 0.1 grams (Approximate) ✔ Flammability rating UL 94V-0 ✔ 12mm Tape and Reel Per EIA St.
ET7272 : These line drivers are pin compatible with 26LS31 in applications where pin 4 = 5V and pin 12 = GND. Internal clamp diodes allow trouble-free operation when driving cable lengths exceeding 100m. Split supplies are provided to minimize standby power dissipation in high voltage applications. The logic should be powered from a regulated 5V supply at the VccBias pin. The output stages may then be powered by a separate supply at VccDrivers, up to 30V. Output voltage swings of 0.3V to VCC-1.9V are typical. The outputs are protected against shorts to ground, shorts to Vcc and to other outputs, by a two-fold scheme of current limiting and thermal shutdown. This assures highly reliable operation in h.
ET7272B : These line drivers are pin compatible with 26LS31 in applications where pin 4 = 5V and pin 12 = GND. Internal clamp diodes allow trouble-free operation when driving cable lengths exceeding 100m. Split supplies are provided to minimize standby power dissipation in high voltage applications. The logic should be powered from a regulated 5V supply at the VccBias pin. The output stages may then be powered by a separate supply at VccDrivers, up to 30V. Output voltage swings of 0.3V to VCC-1.9V are typical. The outputs are protected against shorts to ground, shorts to Vcc and to other outputs, by a two-fold scheme of current limiting and thermal shutdown. This assures highly reliable operation in h.
ET7273C : These line drivers are similar in function to the ET7272, only in an open-collector format. The VCC pin powers the internal logic only. Output voltage is dependent on the customer supplied voltage, up to a maximum of 30V. There is essentially no difference in output swing or performance with VCC (LOGIC) values from 3.5V-30V. Internal clamp diodes allow trouble-free operation when driving cable lengths exceeding 100 meters. The outputs are protected by initiating shutdown when junciton temperatures.