DatasheetsPDF.com

MS20001P

ETC
Part Number MS20001P
Manufacturer ETC
Description Hinge / Butt / Structural / Extruded
Published Nov 6, 2014
Detailed Description INCH-POUND MS20001P 21 May 2012 SUPERSEDING MS20001N 16 November 2010 DETAIL SPECIFICATION SHEET HINGE, BUTT STRUCTURAL...
Datasheet PDF File MS20001P PDF File

MS20001P
MS20001P

Overview
INCH-POUND MS20001P 21 May 2012 SUPERSEDING MS20001N 16 November 2010 DETAIL SPECIFICATION SHEET HINGE, BUTT STRUCTURAL, EXTRUDED This specification sheet is approved for use by all Departments and Agencies of the Department of Defense.
FIGURE 1.
Butt hinge.
AMSC N/A FSC 5340 MS20001P TABLE I.
Dimensions.
A Dash Ref no.
Width Open -2 1.
062 -3 1.
250 -4 1.
500 -5 1.
750 -6 2.
000 -8 2.
000 -9 2.
500 -10 2.
750 -12 3.
375 -14 3.
719 -16 3.
938 E G Min .
612 .
706 .
830 .
955 1.
078 1.
143 1.
328 1.
453 1.
828 2.
038 2.
195 J Dia (b) Q +.
005 K ±.
005 -.
000 Min D dia Max Min R Pin W M dia.
±.
031 ±.
016 ±2° ref.
Rad Max Min Max .
630 .
724 .
056 .
044 .
850 .
975 1.
102 .
076 .
064 1.
167 1.
352 .
056 .
044 1.
477 .
115 .
103 1.
860 .
163 .
149 2.
086 .
210 .
196 2.
243 .
090 .
093 .
187 .
173 .
174 .
135 .
090 75° .
155 .
090 .
156 .
203 .
250 .
183 .
188 .
318 .
302 .
297 .
093 .
133 .
183 .
187 .
173 .
174 .
320 .
304 .
375 .
414 .
398 .
625 .
509 .
491 .
750 .
200 .
180 .
135 .
090 .
188 60° .
240 .
130 45° .
287 .
180 (a) Tolerances for dimensions on pitch shall not be cumulative.
(b) Dimension K must never exceed a full loop or tang, and both ends must be equal within .
020 inch.
INTERCHANGEABILITY RELATIONSHIP, see table II.
MS20001 hinges are not universally interchangeable with AN252 hinges.
TABLE II.
Interchangeability.
Inactive and cancelled AN252-1 AN252-2 AN252-4 AN252-6 AN252-8 AN252-10 Universally interchangeable ------------MS20001-2 MS20001-4 MS20001-6 MS20001-8 MS20001-10 2 MS20001P REQUIREMENTS: 1.
Material Aluminum alloy 2024-T3511 per SAE-AMS-QQ-A-200/3, ASTM-B221, ASTMB241/B241M or aluminum 7075-T73511 per SAE-AMS-QQ-A-200/11, ASTMB241/B241M, ASTM-B221 (see note 6).
Anodize in accordance with MIL-A-8625, Type II, chemical surface treat in accordance with MIL-DTL-5541 (ends of all hinges shall be finished).
Ink stamp MS20001 (dash number) at regular intervals along length of hinge so that any three inch length will have at least one complete identification in figures not less than 0.
060 inch high (see note 5).
2.
Fini...


Similar Datasheet


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site. (Privacy Policy & Contact)