SPST Switch. SW90-0001 Datasheet

SW90-0001 Switch. Datasheet pdf. Equivalent

Part SW90-0001
Description GaAs SPST Switch
Feature www.DataSheet4U.com GaAs SPST Switch, Absorptive, Single Supply, DC - 4 GHz Features n n n n n n n .
Manufacture Tyco Electronics
Total Page 3 Pages
Datasheet
Download SW90-0001 Datasheet



SW90-0001
GaAswww.DataSheet4U.com SPST Switch, Absorptive,
Single Supply, DC - 4 GHz
V 3.00
Features
n Operates DC - 4 GHz on Single Supply
n ASIC TTL / CMOS Driver
n Leadless 4 x 6 mm Chip Scale Plastic Package
n Low DC Power Consumption
n 50 Ohm Nominal Impedance
n Test Boards are Available
n Tape and Reel are Available
Description
M/A-COM's SW90-0001 is a SPST absorptive pHEMT
switch with integral TTL driver. This device is in an MLP
plastic surface mount package. This switch offers excellent
broadband performance and repeatability from DC to 4
GHz, while maintaining low DC power dissipation. The
SW90-0001 is ideally suited for wireless infrastructure
applications.
CSP-1
Electrical Specifications: TA = 25°C
Parameter
Test Conditions
Frequency
Units
Insertion Loss
Isolation
VSWR
VSWR
1 dB Compression
Input IP3
Switching Speed
Vcc
Logic “0”
Logic “1”
Icc
RF1—RF2 (All Logic “1”)
RF1—RF2 (All Logic “0”)
On (RF1, RF2) (All Logic “1”)
Off (RF1, RF2) (All Logic “0”)
Two-tone inputs up to +5 dBm
Ton (50% Control to 10% RF)
Toff (50% Control to 90% RF)
Trise (10% to 90% RF)
Tfall (90% to 10% RF)
Sink Current is 20 µA max.
Source Current is 20 µA max.
Vcc min to max, Logic “0” or “1”
DC - 4.0 GHz
DC - 4.0 GHz
DC - 4.0 GHz
DC - 4.0 GHz
50 MHz
0.5 - 4.0 GHz
50 MHz
0.5-4.0 GHz
dB
dB
Ratio
Ratio
dBm
dBm
dBm
dBm
nS
nS
nS
nS
V
V
V
mA
Min.
25
4.5
0.0
2.0
Typ.
24
30
40
48
32
20
7
2
5.0
5
Max.
0.85
1.5:1
1.5:1
5.5
0.8
5.0
8



SW90-0001
GaAs SPST Switch, Absorptive, Single Supply, DC - 4 GHz
SW90-0001
V 3.00
Pin Configuration 1,2,3
Absolute Maximum Ratings 4,5
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Function
NC
NC
C1
NC
NC
NC
NC
NC
NC
NC
GND
RF2
GND
NC
NC
NC
Pin No.
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Function
NC
NC
VCC
NC
CP2
NC
CP1
NC
VEE
GND
RF1
GND
NC
VEE
NC
VCC
1. NC = No Connection
2. VEE is internally generated and must remain isolated from
external power supplies.
3. Connections and external components shown in func-
tional schematic are required. 0.1 µF Capacitors need to
be located near pins 30 & 32.
Functional Schematic
Parameter
Max. Input Power
0.05 GHz
0.5 - 4.0 GHz
Bias Voltages
VCC
Control Voltage 6
Operating Temperature
Storage Temperature
Absolute Maximum
+27 dBm
+34 dBm
+5.5V
-0.5V to VCC +0.5V
-40°C to +85°C
-65°C to +125°C
4. Operation of this device above any one of these
parameters may cause permanent damage.
5. When the RF input is applied to the terminated port, the
absolute maximum power is +30 dBm.
6. Standard CMOS TTL interface, latch-up will occur if logic
signal is applied prior to power supply.
Truth Table
Control Input
C1
0
1
Condition of the Switch
RF1 to RF2
Off
On
Recommended PCB Layout 7
Specifications subject to change without notice.
n North America: Tel. (800) 366-2266
n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298
n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
Visit www.macom.com for additional data sheets and product information.
7. Application Note C2083 is available on line at
www.macom.com
2





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)