DatasheetsPDF.com

Ceramic Capacitors. GJ218 Datasheet

DatasheetsPDF.com

Ceramic Capacitors. GJ218 Datasheet






GJ218 Capacitors. Datasheet pdf. Equivalent




GJ218 Capacitors. Datasheet pdf. Equivalent





Part

GJ218

Description

Chip Monolithic Ceramic Capacitors



Feature


Please read CAUTION and Notice in this c atalog for safety. This catalog has onl y typical specifications. Therefore you are requested to approve our product s pecification or to transact the approva l sheet for product specification, befo re your ordering. C02E8.pdf 01.7.26 w ww.DataSheet4U.com Chip Monolithic Cer amic Capacitors for Smoothing e g e s Features 1. Heat g.
Manufacture

Murata Manufacturing

Datasheet
Download GJ218 Datasheet


Murata Manufacturing GJ218

GJ218; eneration is low at high frequency becau se of low dielectric loss. 2. Compared with aluminum electrolytic capacitors, capacitance can be lower to obtain the same smoothing performance. 3. Ceramic capacitor has no polarity and ensures l ong life time. L W Part Number GJ221 B GJ231M GJ232N GJ232C GJ232R GJ243R GJ 243X s Applications 6 • DC-DC conv erter • Noise elimin.


Murata Manufacturing GJ218

ation LCD bias circuit (Use for only alu mina, paper or glass epoxy board) Rated Voltage (Vdc) 6.3 6.3 6.3 6.3 10 50 50 100 Dimensions (mm) L W T e min. 2.0 ±0.1 1.25 ±0.1 1.25 ±0.1 0.2 to 0.7 3.2 ±0.15 1.6 ±0.15 1.15 ±0.1 0.3 to 0.8 1.35 ±0.15 3.2 ±0.3 2.5 ±0.2 1. 6 ±0.15 0.3 1.8 ±0.2 1.8 ±0.2 4.5 ± 0.4 3.2 ±0.3 0.3 2.2 ±0.3 g min. 0.7 1.5 1.0 2.0 Part Number GJ221BF.


Murata Manufacturing GJ218

50J106ZD01 GJ231MF50J226ZD01 GJ232CF50J4 76ZD01 GJ243RF50J107ZD11 GJ232NF51A226Z D01 GJ232RF51H475ZD01 GJ243XF51H106ZD12 GJ232RF52A105ZD01 TC Y5V Y5V Y5V Y5V Y5V Y5V Y5V Y5V Capacitance (µF) 10 + 80.-20% 22 +80.-20% 47 +80.-20% 100 +80 .-20% 22 +80.-20% 4.7 +80.-20% 10 +80.- 20% 1 +80.-20% Length L (mm) 2.00 3.20 3.20 4.50 3.20 3.20 4.50 3.20 Width W (mm) 1.25 1.60 2.5.

Part

GJ218

Description

Chip Monolithic Ceramic Capacitors



Feature


Please read CAUTION and Notice in this c atalog for safety. This catalog has onl y typical specifications. Therefore you are requested to approve our product s pecification or to transact the approva l sheet for product specification, befo re your ordering. C02E8.pdf 01.7.26 w ww.DataSheet4U.com Chip Monolithic Cer amic Capacitors for Smoothing e g e s Features 1. Heat g.
Manufacture

Murata Manufacturing

Datasheet
Download GJ218 Datasheet




 GJ218
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
www.DataSheet4U.com
Chip Monolithic Ceramic Capacitors
for Smoothing
C02E8.pdf 01.7.26
s Features
1. Heat generation is low at high frequency because of
low dielectric loss.
2. Compared with aluminum electrolytic capacitors,
capacitance can be lower to obtain the same
smoothing performance.
3. Ceramic capacitor has no polarity and ensures long
life time.
s Applications
6 • DC-DC converter
• Noise elimination LCD bias circuit
(Use for only alumina, paper or glass epoxy board)
Part Number
GJ221BF50J106ZD01
GJ231MF50J226ZD01
GJ232CF50J476ZD01
GJ243RF50J107ZD11
GJ232NF51A226ZD01
GJ232RF51H475ZD01
GJ243XF51H106ZD12
GJ232RF52A105ZD01
TC
Y5V
Y5V
Y5V
Y5V
Y5V
Y5V
Y5V
Y5V
Rated Voltage
(Vdc)
6.3
6.3
6.3
6.3
10
50
50
100
ege
Part Number
GJ221B
GJ231M
GJ232N
GJ232C
GJ232R
GJ243R
GJ243X
L
2.0 ±0.1
3.2 ±0.15
3.2 ±0.3
4.5 ±0.4
LW
Dimensions (mm)
W T e min.
1.25 ±0.1 1.25 ±0.1 0.2 to 0.7
1.6 ±0.15 1.15 ±0.1 0.3 to 0.8
1.35 ±0.15
2.5 ±0.2 1.6 ±0.15 0.3
1.8 ±0.2
3.2 ±0.3
1.8 ±0.2
2.2 ±0.3
0.3
g min.
0.7
1.5
1.0
2.0
Capacitance
(µF)
10 +80.-20%
22 +80.-20%
47 +80.-20%
100 +80.-20%
22 +80.-20%
4.7 +80.-20%
10 +80.-20%
1 +80.-20%
Length L
(mm)
2.00
3.20
3.20
4.50
3.20
3.20
4.50
3.20
Width W
(mm)
1.25
1.60
2.50
3.20
2.50
2.50
3.20
2.50
Thickness T
(mm)
1.25
1.15
1.60
1.80
1.35
1.80
2.20
1.8
30




 GJ218
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
C02E8.pdf 01.7.26
Specifications and Test Methods
Specifications and Test Methods
No. Item
1 Operating
F5 : Y30°C to 85°C
Temperature Range
Specification
2 Rated Voltage
See the previous pages.
3 Appearance
4 Dimensions
No defects or abnormalities.
Within the specified dimension.
5 Dielectric Strength No defects or abnormalities.
Insulation
6
Resistance
More than 10,000Mor 500· F.
(Whichever is smaller)
7 Capacitance
Within the specified tolerance.
0.07 max. (50/100V)
Dissipation Factor
8 0.09 max. (10/16/25V)
(D.F.)
0.15 max. (6.3V)
Test Method
The rated voltage is defined as the maximum voltage which
may be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage, VP-P or VO-P,
whichever is larger, shall be maintained within the rated voltage
range.
Visual inspection.
Using calipers.
No failure shall be observed when 250% of the rated voltage is
applied between the both terminations for 1 to 5 seconds, pro-
vided the charge/discharge current is less than 50mA.
The insulation resistance shall be measured with a DC voltage
not exceeding the rated voltage at normal temperature and
humidity and within 2 minutes* of charging.
*5minutes for c>47µF.
The capacitance/D.F. shall be measured at 25°C at the fre-
quency and voltage shown in the table.
Capacitance Frequency
CV10µF
1±0.1kHz
CG10µF 120±24Hz
Voltage
1±0.2Vrms
0.5±0.1Vrms
Capacitance
9 Temperature
Characteristics
Char.
Temp.
Range
Reference Cap. Change
Temp.
Rate
F5 -30 to +85°C 25°C Within+-8222%
No removal of the terminations or other defects shall occur.
c
Adhesive Strength
10
of Termination
b
a
Fig.1
Solder resist
Baked electrode or
copper foil
Vibration
11 Resistance
Item
Appearance
Capacitance Change
ID. .F.
Dielectric Strength
Frequency
No defects or abnormalities.
Within the specified tolerance.
50, 100V 10, 16, 25V 6.3V
0.07 max. 0.09 max. 0.15 max.
No failure
The capacitance change shall be measured after 5 min. at
each specified temperature stage.
The ranges of capacitance change compared to 25°C with the
temperature ranges shown in the table shall be within the spec-
ified ranges.
Solder the capacitor on the testing jig (glass epoxy board)
shown in Fig.1 using a eutectic solder. Then apply 5N force in
parallel with the test jig for 10±1 sec. The soldering shall be
done either with an iron or using the reflow method and shall be
conducted with care so that the soldering is uniform and free of
defect such as heat shock.
Type
GJ218
GJ221
GJ231
GJ232
GJ243
a
1.0
1.2
2.2
2.2
3.5
bc
3.0 1.2
4.0 1.65
5.0 2.0
5.0 2.9
7.0 3.7
(in mm)
Solder the capacitor on the testing jig (glass epoxy board) in
the same manner and under the same conditions as (10).
The capacitor shall be subjected to simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, shall be
traversed in approximately 1 minute. This motion shall be
applied for a period of 2 hours in each 3 mutually perpendicular
directions (total of 6 hours).
Continued on the following page.
6
31




 GJ218
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
C02E8.pdf 01.7.26
Specifications and Test Methods
Continued from the preceding page.
No. Item
Specification
No cracks or marking defects shall occur.
R230
20 50 Pressurizing
speed : 1.0mm/sec.
Pressurize
Specifications and Test Methods
Test Method
Solder the capacitor to the test jig (glass epoxy boards) shown
in Fig.2 using a eutectic solder. Then apply a force in the direc-
tion shown in Fig.3 for 5±1 sec. The soldering shall be done
either with an iron or using the reflow method and shall be con-
ducted with care so that the soldering is uniform and free of
defects such as heat shock.
b
ø4.5
12 Deflection
Capacitance meter
45 45
Flexure : V1
a
100 t=1.6mm
Fig.2
Fig.3
Type
a
b
c
6 GJ218
1.0
3.0
1.2
GJ221
1.2
4.0 1.65
GJ231
2.2
5.0
2.0
GJ232
2.2
5.0
2.9
GJ243
3.5
7.0
3.7
(in mm)
13
Solderability of
Termination
14
Resistance to
Soldering Heat
75% of the terminations is to be soldered evenly and continu-
ously.
The measured values shall satisfy the values in the following
table.
Item
Appearance
Capacitance Change
I. R.
D.F.
Dielectric Strength
Specification
No marked defect
Within T20%
More than 10,000Mor 500· F
(Whichever is smaller)
50, 100V 10, 16, 25V 6.3V
0.07 max. 0.09 max. 0.15 max.
No failure
Immerse the capacitor first ethanol (JIS-K-8101)a solution of
rosin (JIS-K-5902) (25% rosin in weight proportion), then in an
eutectic solder solution for 2±0.5 seconds at 230±5°C after pre-
heating in the following table. then set it for 48±4 hours at room
temperature and measure.
The capacitor shall be set for 48±4 hours at room temperature
after one hour heat of treatment at 150.+–100 °C.
Immerse the capacitor in a eutectic solder solution at 270± 5°C
for 10±0.5 seconds after preheating in the flowing table. Then
set it for 48T4 hours at room temperature and measure.
15
Temperature
Cycle
No marking defects.
Item
Appearance
Capacitance Change
I. R.
D.F.
Dielectric Strength
Specification
No marked defect
Within T20%
More than 10,000Mor 500· F
(Whichever is smaller)
50, 100V 10, 16, 25V 6.3V
0.07 max. 0.09 max. 0.15 max.
No failure
The capacitor shall be set for 48±4 hours at room temperature
after one hour heat of treatment at 150+–100 °C.
Then measure for the initial measurement. Fix capacitor to the
supporting jig in the same manner and under the same condi-
tions as in (10) and conduct the five cycles according to the
temperature and time shown in the following table.
Set it for 48±4 hours at room temperature, then measure.
Step
1
Min. Operating
Temp. (ºC) Temp.a-+a03a
Time (min.)
30T3
2
Room
Temp.
2 to 3
3
Max. Operating
Temp.a+-a03a
30T3
4
Room
Temp.
2 to 3
16 Humidity
Steady State
No marking defects.
Item
Appearance
Capacitance Change
I. R.
D.F.
Dielectric Strength
Specification
No marked defect
Within T30%
More than 1,000Mor 50· F
(Whichever is smaller)
50, 100V 10, 16, 25V 6.3V
0.1 max. 0.125 max. 0.2 max.
No failure
Set the capacitor for 500±12 hours at 40±2°C and 90 to 95%
humidity. Take it out and set it for 48T4 hours at room tempera-
ture, then measure.
17 Humidity
Load
No marking defects.
Item
Appearance
Capacitance Change
I. R.
D.F.
Dielectric Strength
Specification
No marked defect
Within T30%
More than 500Mor 25· F
(Whichever is smaller)
50, 100V 10, 16, 25V 6.3V
0.1 max. 0.125 max. 0.2 max.
No failure
Apply the rated voltage for 500±12 hours at 40±2°C and 90 to
95% humidity and set it for 48±4 hours at room temperature,
then measure. The charge/discharge current is less than
50mA.
Continued on the following page.
32






Recommended third-party GJ218 Datasheet






@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)